MINI SKELETON-90 USER’S MANUAL
TABLE OF CONTENTS INTRODUCTION 1.1 Case Specifications……………………………………………………………………………………….. 3 1.2 Diagram………………………………………………………………………………………………………… 3 1.3 EP-90 Power Supply Specifications……………………………………………………………….. 4 HARDWARE INSTALLATION GUIDE 2.1 Removing/Replacing the Component Tray…………………………………………………… 5 2.2 Motherboard Installation……………………………………………………………………………… 5 2.3 5.25” Device Installation………………………………………………………………………………. 6 2.4 2.5” Device External Installation…………………………………………………………………… 6 2.5 2.
MINI SKELETON-90 USER’S MANUAL THINK BEYOND THE BOX At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s computer enclosures.
CASE SPECIFICATIONS 1.1 Case Type Color Dimensions Weight Cooling Drive Bays Motherboard Size Front I/O Panel Power Supply 1.2 Open-Air Mini-ITX Metallic Silver 7.5” (H) x 8.3” (W) x 9.1” (D) 190mm (H) x 210mm (W) x 230mm (D) 5.5 lbs / 2.5 kg 1 x 150mm 3-Speed Blue LED Overhead Fan 1 x 70mm Rear Intake Fan 2 x Quick Release 2.5” Hard Drive Bays 1 x Quick Release 5.25" Bay 2 x Externally Mounted 2.5" Hard Drive Bays Mini-ITX 2 x USB 2.
1.3 EP-90 POWER SUPPLY SPECIFICATIONS The Mini Skeleton-90 is powered by an EP-90 power adapter. Input Characteristics: Rated Voltage 100 VAC ~ 240 VAC Input Voltage Range 90 VAC ~ 264 VAC Frequency Range 50 Hz ~ 60 Hz Output Characteristics: Rated Power 90W Rated Voltage 19V Voltage Range 18.4V ~ 20.0V Output Current 0A ~ 4.7A Ripple & Noise 300 mV The EP-90 is rated at least 85% efficient at 100 VAC and 240 VAC input voltage and maximum load.
HARDWARE INSTALLATION GUIDE This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult your motherboard user’s manual for specific mounting instructions and troubleshooting. Before proceeding, check the manual for your CPU cooler to find out if there are steps you must take before installing the motherboard. 2.1 REMOVING/REPLACING THE COMPONENT TRAY 1. With the rear of the case facing you, remove the thumbscrew at the left side of the Component Tray. 2.
2.3 5.25” DEVICE INSTALLATION 1. In your tool bag, find one of the black screws and attach one to your 5.25” device at the right upper side. 2. While facing the front of the case, insert your 5.25” device into the slot in the Component Tray until it locks into position. Note: It may be necessary to remove the side screens as detailed in section 2.5 to effectively route cables to your device.
2.5 2.5” DEVICE FRAME-MOUNTED INSTALLATION Your Antec Mini Skeleton case has the ability to mount up to two additional 2.5” devices externally on the Frame for additional storage capacity. 1. Align your 2.5” device with the included 2.5” device mounting plates and secure them together with the included screws. 2. Hook the mounting plate along the sides of the Frame. Note: It may be necessary to remove the motherboard tray and/or side screens as detailed in section 2.
CONNECTING THE FRONT I/O PORTS 3.1 USB 2.0 PORTS Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check your motherboard user’s manual to ensure that it matches the table below: 3.2 AC’97 AND HD AUDIO PORTS Connected to your front I/O panel there is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio) connector.
3.3 POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Connected to the front of the Mini Skeleton-90 case Frame are LED and switch leads for power, reset, and HDD LED activity. Attach these to the corresponding connectors on your motherboard. Consult your motherboard manual for specific pin positions. For LEDs, colored wires are positive (+). White or black wires are negative (–). If the LED does not light up when the system is powered on, try reversing the connection.
COOLING SYSTEM 4.1 150MM OVERHEAD TRICOOL™ FAN Because of the Mini Skeleton’s unique and innovative open-air design, one 150mm intake fan cools all of your system components. This overhead fan is adjustable to three different speeds, allowing you to choose the best speed suited to your needs. The default speed of the fan is Low. 150mm Fan Specifications: Size: Rated Voltage: Operating Voltage: Speed (RPM) 2600 (max.) 4.2 150mm DC 12V 10.8V~13.2V Input Current 0.3A (max.) 2000 0.22A 1500 0.
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Technical Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2009 Antec, Inc. All rights reserved. All trademarks are the property of their respective owners.
