MINUET 300 User’s Manual 1
TABLE OF CONTENTS Minuet 300 ...................................................... 2 Setting Up ........................................................ 2 Motherborad Installation .................................. 2 Power/LED Connections .................................. 3 Connecting The USB Ports .............................. 3 Connecting The IEEE 1394 (FireWire®, i.Link®) Port ................................... 4 Connecting The Audio Ports ............................ 4 Drive Installation ..........
The high quality of our products is assured by a continuous process of refinement of their technical features. Therefore, it is possible that your product may differ in some respect from the descriptions contained in this manual. This is not a problem– it is an improvement. All features, descriptions and illustrations contained herein are valid as of the date of publication. Disclaimer This manual is intended only as a guide for Antec’s Computer Enclosures.
2. 3. 4. 5. 6. Line up your motherboard with the standoff holes, and determine which ones line up and remember where they are. Not all motherboards will match with all of the provided screw holes, and this is not necessary for proper functionality. (In other words there will likely be extra holes.) Some standoffs may be pre-installed for your convenience. Lift up and remove your motherboard. Screw in the brass standoffs to the threaded holes that line up with your motherboard’s mounting holes.
® ® CONNECTING THE IEEE 1394 (FIREWIRE , I.LINK ) PORT You will find a single 10-pin connector on a cable attached to the front IEEE 1394 connection. This is an Intel standard connector, which is keyed so that it can’t be accidentally reversed as long as it is connected to a proper Intel standard motherboard header. Connect the 10-pin connector to your motherboard header so that the blocked pin fits over the missing header pin.
2. 3. 4. Lift up and slide the drive cage from the case. Place the cage upside down on a flat surface. Note: You must install the external devices first, before installing the internal 3.5” device. 5. Slide the external 5.25” device into the drive cage from the front. Since the drive cage is upside down, your drive should be too so that it will be properly orientated once the cage is installed in the Minuet II. 6.
Specifications: Size: 80 x 80 x 25.4mm Rated Voltage: 12V Operating Voltage: 10.2V ~ 13.8V Speed Input Current High 2600 RPM 0.2A (Max.) Medium 2000 RPM Low 1500 RPM Air Flow Static Pressure Acoustical Noise Input Power 0.96 m³ / min 3.04 mm-H2O (34 CFM) (0.12 inch-H2O) 30 dBA 2.4W 0.15A 0.74 m³ / min 1.79 mm-H2O (26 CFM) (0.07 inch-H2O) 24 dBA 1.8W 0.1A 0.55 m³ / min 1.00 mm-H2O (20 CFM) (0.03inch-H2O) 18 dBA 1.
1 2 3 4 14 13 12 5 7 6 8 11 9 Minuet 300 - Explorer Description # Description # Description 1 Thumbscrews 8 3.5” Drive Bay Cover 2 Top Panel with Vent 9 Front Bezel 3 Power Supply 10 5.
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Sydneystraat 33 3047 BP Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com Antec Quality 3-Year parts and labor warranty (A3Q) See details at: http://www.antec.com/warranty.php © Copyright 2005Antec, Inc. All rights reserved.
