ISK 300-65 USER’S MANUAL
TABLE OF CONTENTS INTRODUCTION 1.1 Case Specifications.…..…………………………………………………………………………………..3 1.2 Diagram…………………………………………………………………….…………………………………. 3 1.3 Power Supply Specifications…………………………………………………………………………. 4 HARDWARE INSTALLATION GUIDE 2.1 Removing the Top Panel.……………………………………………………………………………….5 2.2 Removing the Drive Tray Assembly……….……………………………………………………… 5 2.3 Motherboard Installation..……………………………………………………………………………. 5 2.4 Internal 2.5” Device Installation……………………………………………………………………. 5 2.
ISK 300-65 USER’S MANUAL At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s computer enclosures.
1.1 CASE SPECIFICATIONS Case Type Mini-ITX Desktop Color Black Dimensions 96mm (H) X 222mm (W) X 328mm (D) 3.8” (H) x 8.7” (W) x 12.9” (D) Net Weight 5.5 lbs / 2.5 kg Cooling Drive Bays 1 x Side 80mm TriCool™ fan 3 Drive Bays: - 1 x External 5.25” slim drive bay - 2 x Internal 2.5” drive bays Expansion Slots 1 x Half-height slot Motherboard Size Mini-ITX 2 x USB 2.0 1 x eSATA AC’97 / HD Audio In and Out EP-65 power adapter and PCB Front I/O Panel Power Adapter 1.2 DIAGRAM 1. 2. 3. 4. 5.
1.3 POWER SUPPLY SPECIFICATIONS The ISK 300-65 is powered by an EP-65 power adapter. Input characteristics: Rated Voltage 100 VAC ~ 240 VAC Input Voltage Range 90 VAC ~ 264 VAC Frequency Range 50 Hz ~ 60 Hz Output characteristics: Rated Power 65W Rated Voltage 19V Output Current 0A ~ 3.42A Voltage Range 18.4V ~ 20.
HARDWARE INSTALLATION GUIDE 2.1 REMOVING THE TOP PANEL Place the case flat on an even, stable surface. 1. 2. 3. Remove the three thumbscrews from the rear of the top panel. Grip the top panel and slide it back several inches until it stops. Grip the panel from the sides and lift it up until it pulls completely free of the main chassis. Note: Do not use your fingernails to pry or lift the panels. 2.2 REMOVING THE DRIVE TRAY ASSEMBLY Remove the top panel as detailed in section 2.1. 1. 2. 3.
2.4 INTERNAL 2.5” DEVICE INSTALLATION Remove the top panel as described in section 2.1. Included at the top of the drive tray assembly is a HDD tray that can support up to two 2.5” devices. 1. 2. 3. 4. 5. 6. On the right side of the drive tray assembly, remove the thumbscrew holding the HDD tray to the rest of the device. Slide the HDD tray back a centimeter so the locking hinges unhook. Pull the HDD tray away from the drive tray assembly. Align your 2.5” device with the HDD tray.
CONNECTING THE FRONT I/O PORTS 3.1 USB 2.0 Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the motherboard manual to ensure that it matches the table below: 1 2 Pin 9 10 Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Ground 1 8 Ground 2 9 Key (No Connection) 10 Empty Pin 3.2 ESATA You will find a SATA connector on a cable attached to the front ports.
3.4 POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Connected to your front panel are LED and switch leads for power, reset, and HDD LED activity. Attach these to the corresponding connectors on your motherboard. Consult your motherboard user’s manual for specific pin header locations. For LEDs, colored wires are positive ( + ). White or black wires are negative ( – ). If the LED does not light up when the system is powered on, try reversing the connection.
COOLING SYSTEM 4.1 TRICOOL™ EXHAUST FAN There is a 80 x 25mm TriCool™ fan pre-installed on the right-hand side of the case. It has an external, three-speed switch that allows you to choose between quiet performance, or maximum cooling. The default speed setting is Low. The fan is mounted so that air blows out of the case. There are externally accessible switches for these fans located at the rear of your case. Size: Rated Voltage: Operating Voltage: 80 x 25mm TriCool™ fan 12V 10.2V - 13.
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2009 Antec, Inc. All rights reserved. All trademarks are the property of their respective owners.
