User Manual for the Antari M-1 Mobile Fog Machine Congratulations on the purchase of your new ANTARI M-1 Mobile Fog Machine Save and read these instructions Bitte lesen Sie und sichern Sie diese Anweisungen Lisez et Gardez ces instructions © 2007 Antari Lighting and Effects Ltd.
M-1 Mobile Fogger Introduction Thank you for choosing Antari’s M-1 Mobile Fogger. You now own a sturdy and portable state-of-the-art fog machine. Prior to use, we suggest that you carefully read all of the instructions. By following the suggestions found in this user manual, you can look forward to exceptional performance from your Antari Mobile Fog Machine for years to come. Please follow these operations, safety and maintenance instructions to ensure a long and safe life for your fog machine.
Never aim the output nozzle directly at people. Fog machine output is hot. Avoid coming within 50 cm of the output nozzle during operation. Place the fog machine in a well-ventilated area. Never cover the vents on the front of the M-1. Never aim the output nozzle at open flames. The output nozzle becomes hot during operation. Keep flammable materials at least 50 cm away from the nozzle. Always allow your Antari Fog Machine to cool down before attempting to clean or service it.
Setup Remove all packing materials from the fog machine. Check that all foam and plastic padding is removed, especially in the nozzle area. Fill with Antari Fog Liquid (FLM-05) or dealer recommended high-quality water-based fog fluid. types of fluid can damage the unit. Charge the battery. Any other When filled, place cap back on liquid tank. Plug the adaptor into a grounded electrical outlet. will light up when it is connected to the power supply.
To select operation mode 1. Slide the switch towards the back of the M-1 (towards the cap on the liquid tank). To select operation mode 2. Slide the switch towards the front of the M-1 (towards the nozzle). When an optional remote is connected, please see the detailed instructions for their operation below. The machine will fo until the battery charge runs down or the M-1 runs out of fog liquid.
Optional Dummy Battery and Power Adaptor Set Users can purchase the optional dummy battery and power adaptor for M1. (Item Number: DCP-12) The power adaptor can be used at AC100~240V power outlets. It can transform AC power into DC12V and power the M-1 by the dummy battery.
M-1 ͘೩ёᙳ፟(ᄊё)ֹϡᄲځ३ ऽಈଋјࠎ Antari M-1 ͘೩ёᙳ፟۞ֹϡ۰. 感謝您選用 Antari 煙霧機產品,現在您已經擁有高科技的專業煙霧機,在開始使用之前,我們建議您 先仔細閱讀本說明書,遵循使用手冊中的說明,這會有助於您在使用 Antari 煙霧機時得心應手,達到 最滿意的煙霧效果,對於機器的使用壽命也更為延長。 ፟ጡఢॾ! 煙霧輸出速率: 300 立方英呎/每分鐘 功率: 75 瓦特 油桶容量: 110 c.c. 電池規格: 直流 12V /2.3Ah 耗油速率: 2c.c./每分鐘 適用煙霧水: Antari FLM-05 煙霧水 選購控制器: MCT-1 (定時線控器) MCR-1 (無線搖控器) 重量: 1.8 公斤(M-1 機身及電池) 5.5 公斤(M-1 含飛行箱,電池,充電器及 500c.c.
ᔖҺ፼፵۞щБֹϡ͞ё! 機器僅限成人使用,放置煙霧機之地點應避免兒童可及之處,機器使用中請時常注意機器狀況。 煙霧機所產生的煙霧溫度較高,機器運作時,請遠離噴嘴 50 公分以上。 請勿將機器噴嘴對著人體及動物直射。 請將煙霧機放置於通風良好的地方,請勿遮蓋機器散熱部分,並勿將機器噴嘴對準火舌。 當機器運作時,噴嘴輸出部分之溫度非常高,故請將任何物品放置遠離機器 50 公分以上。 清潔、從事維護及收納機器時,請先確認機器已經完全冷卻。 ᔖҺᘕࠓ۞щБֹϡ͞ё! 請勿將電池暴露在高溫下,遠離火舌並請勿任意在機器操作時,拆卸零件。 請勿將任何可燃性液體( 如油脂, 瓦斯, 香水),放置於煙霧油槽中,並在使用前詳細閱讀說明書。 請使用代理商所推薦的 Antari 高品質 FLR / FLG 水性煙霧油(M-1 只使用 FLM-05 煙霧油),若任意 使用其他煙霧油,將可能導致堵管現象甚至造成內部零件腐蝕。 請確認煙霧油槽中有足夠的煙霧油,以免造成煙霧機幫浦空轉過熱。 若在無填裝煙霧油的狀態下運轉機器,將導致幫浦與加熱管的損壞。
請注入 Antari FLM-05 高品質煙霧油,並仔細蓋上油蓋。 電池充電方式。請將充電器接上電源插頭,在接上電源時電池上的綠燈會亮者,然後將電 池連接充電。請注意首次使用電池必須充滿八個小時,往後充電時間大約 2~3 個小時。 充完電後約能連續使用 10~12 分鐘。 電池安裝至機器時,請注意方向(貼紙面朝上-如圖示)。 放置電池時請稍微傾斜機器,會更容易置入,銀色卡榫為固定電池之用。 請確認電池放置時的位置正確(如附圖)。 當第一次按下按鈕時,機器把手前方的綠燈會閃爍,表示電池已經充電飽和。 當紅色燈開始閃爍時,表示電池需要充電,但這時機器仍能稍微運作一陣短暫時間。 ፆү፟ጡ! 啟動噴煙動作的開關位於機器提把的上方有兩種操控方式可選擇,請注意 M-1 機身右側有一個開 孔,開孔中有一個小開關,可利用此小開關來切換操作模式。 操作模式 1: 將右側孔中的小開關往油桶蓋方向撥,可將機器設定在一號操作模式,在此模式下, 持續壓著把手上的開關,M-1 會持續噴煙動作,而一旦鬆開開關,機器就會停止噴煙。 操作模式 2: 將右側孔中的小開關往噴嘴方向撥,可將
M1 機器可搭配兩種選購控制器 1. MCT-1 定時控制器: 此控制器是透過一條總長 8 公尺的電線與 M1 連接,內建設定的持續 煙霧輸出為 10 秒,而每次煙霧的輸出間距可透過控制器上的旋鈕來設定於 3 至 220 秒之間。 2.
機器不使用需收納之前請先清潔機器並確定將油桶清空,拆下控制器與電源線收好,整套 機器與配件請存放於乾燥陰涼處,每月固定溫機一次,可保護機器較不受潮。 11
C08M01001 12