F-5D Fazer User Manual English © 2014 Antari Lighting and Effects Ltd.
User Manual - English Safety Information Please read the following safety information carefully before operating the machine. This information includes important safeguards about installation, usage, and maintenance. Pay attention to all warning labels and instructions in this manual and printed on the machine. If you have questions about how to operate the machine safely, please contact your local Antari dealer for help. ․ Keep this device dry.
․ If the machine fails to work, unplug the machine and stop operation immediately. Contact your local Antari dealer for advise. ․ Before transporting the machine, make sure the fluid tank is completely drained. ․ Fog fluid may present health risks if swallowed. Do not drink fog fluid. Store it securely. In case of eye contact or if fluid is swallowed, immediately look for medical advice.
Product Overview WDMX Wireless Solution Blue LCD screen, Timer mode, Volume mode Neutrik PowerCon Breaker Fog Output Nozzle XLR 3-Pin DMX Connector XLR 5-Pin DMX Connector Setting Up Step 1: Place the machine on a flat surface and in a suitable large area with at least 50 cm open space around the machine. Step 2: Fill the fluid tank with Antari approved fluid. Step 3: Connect the machine to suitable rated power supply.
Language Setting To switch the language used for the control interface, press the [Menu] button BEFORE turning on the machine and HOLD it until the LCD screen flashes twice. After the two flashes, press [Menu] to choose the language: English and 中文 (Chinese). Operation Control Panel Operation The machine can be operated with the onboard digital control interface.
Timer Duration XXX Sec Set duration from 1 to 120 seconds Timer Output XXX % Set output volument from 1 to 100 % Volume Output XXX % Fan Speed Set output volume from 1 to 100 % Set fan speed from 20 to 100% XXX % DMX-512 W-DMX Address: XXX W-DMX Power Set DMX/W-DMX address from 1 to Address: XXX 511 Turn On/Off W-DMX XX W-DMX Reset XX DMX Mode Unlink from a W-DMX transmitter DMX Mode XXXX DMX Mode 2 Ch Air Pump Sensor 1 Ch DMX Mode Sync Turn On/Off air pump sensor XX Run Last Settin
indicates pin assignment information. Pin Function 1 Ground 2 Data- 3 Data+ DMX Operation Making the DMX Connection – Connect the machine to a DMX controller or to one of the machines in the DMX chain. The machine uses a 3-pin or 5-pin XLR connector for DMX connection, the connector is located on the front of the machine. Address Setup – Use control menu to set DMX address. The machine occupies 2 control channels.
DMX Channel Function Channel Mode Channel Value 0-4 Function Faze off 1 5-255 Faze 1-100% 2 0-4 Fan 20% 2 5-255 0-4 Fan 21-100% Faze off Fan 100% 1 1 5-255 Faze 1-100% Fan 100% 0-4 Faze Off Fan 20% Sync 1 5-255 Faze 1-100% Fan 21-100% Fluid Only use Antari FLG water-based liquid for the F-5D Fazer. The machine is tested and calibrated with this liquid to get the best output performance.
pump or heater. ․ It is recommended to run the machine on a monthly basis in order to achieve best performance and output condition. ․ Excessive dust, liquid and dirt built up will degrade performance and cause overheating. Replacing the Fuse Disconnect AC power before replacing fuse. Only replace fuse with same type and rating. Step 1: Disconnect power cord from supply. Step 2: Use a flat-head screwdriver to release fuse holder. Step 3: Replace fuse with exact same type and rating as indicated below.
Antari F-5 Ready To Faze Machine ready for operation Machine has detected overheat on heater unit and will not Warning! Heater Overheat operate, please contact local distributor/dealer for service and support. Machine can not heat up and will not operate. Please contact Warning! Temp Error Warning! Fluid Backflow local distributor/dealer for service and support. Fluid backflow into airpump detected, machine will not operate. Please contact local distributor/dealer for service and support.
C08F5D000 12
