Antaira Industrial Ethernet Switches LMX-1002G-SFPeries User Manual V1.0 LMX-1002G-SFP Series 10-Port Industrial Gigabit Managed Ethernet Switch, with 8*10/100/1000Tx and 2*100/1000 SFP Slots Hardware Manual Version 1.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 © Copyright 2018 Antaira Technologies, LLC All Rights Reserved This document contains information, which is protected by copyright. Reproduction, adaptation or translation without prior permission is prohibited, except as allowed under the copyright laws.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 FCC Warning This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 Table of Contents 1. Introduction ................................................................. 1 1.1 Product Overview 1 1.2 Product Software Features 1 1.3 Product Hardware Features 2 1.4 Package Contents 3 1.5 Safety Precaution 3 2. Hardware Description ................................................. 4 2.1 Physical Dimensions 4 2.2 Front Panel 5 2.3 Top View 5 2.4 LED Indicators 6 2.
Antaira Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 1. Introduction All Antaira industrial managed switches come with a pre-installed “user friendly” web console interface, which allows users to easily configure and manage the units, whether one is using a serial console and command line interface (CLI) commands like Telnet, SSH, HTTP (Web GUI) or simple network management protocols (SNMP). 1.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 1.4 Package Contents 1– LMX-1002G-SFP series: 10-port industrial gigabit managed Ethernet switch, with 8*10/100/1000Tx and 2*100/1000 SFP slots 1-Product CD 2-W all mounting brackets and screws 1-RJ45 to DB9 Serial Console cable 1-DC cable –18 AWG & DC jack 5.5x2.1mm 1.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 2. Hardware Description 2.1 Physical Dimensions Figure 2.1, below, shows the physical dimensions of Antaira’s LMX-1002G-SFP series: 10-port industrial gigabit managed Ethernet switches with 8*10/100/1000Tx and 2*100/1000 SFP slots. (W x D x H) is 54mm x 99mm x 142mm Figure2.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 2.2 Front Panel The front panel of the LMX-1002G-SFP series industrial gigabit managed Ethernet switch is shown below in Figure 2.2. Figure 2.2 The Front Panel of LMX-1002G-SFP Series 2.3 Top View Figure 2.3, below, shows the top panel of the LMX-1002G-SFP series switch that is equipped with one 6-pin removal terminal block connector for dual DC power inputs 12~48VDC. Figure2.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 2.4 LED Indicators There are LED light indicators located on the front panel of the industrial Ethernet switch that display the power status and network status. Each LED indicator has a different color and has its own specific meaning, see below in Table 2.1.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 2.6 Ethernet Ports RJ-45 Ports RJ-45 Ports (Auto MDI/MDIX): The RJ-45 ports are auto-sensing for 10Base-T, 100Base-TX, or 1000Base-T connections. Auto MDI/MDIX means that the switch can connect to another switch or workstation without changing the straight-through or crossover cabling. See the figures below for straight-through and crossover cabling schematics.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 2.7 Cabling Use the four twisted-pair, category 5e, or the above cabling for the RJ-45 port connections. The cable between the switch and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) in length. Caution: Please employ optional optical transceiver (SFP) that complies with IEC 60825-1 and classified as Class 1 laser product.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 To remove the LC connector from the transceiver, please follow the steps shown below: 1. Press the upper side of the LC connector from the transceiver and pull it out to release as shown below in Figure 2.9. Figure 2.9 Remove LC Connector 2. Push down the metal clasp and pull the transceiver out by the plastic part as shown below in Figure 2.10. Figure 2.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 2.8 Wiring the Power Inputs Caution: Please follow the steps below when inserting the power wire. 1. Insert the positive and negative wires into the PWR1 (V1+, V1-) and PWR2 (V2+, V2-) contacts on the terminal block connector as shown below in Figure 2.11. Figure 2.11 - Power Terminal Block 2. Tighten the wire-clamp screws to prevent the wires from loosening, as shown below in Figure 2.12. Figure 2.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 Caution: The wire gauge for the terminal block should range between 12 ~ 24AWG If only using one power source, jumper Pin 1 to Pin 5 and Pin 2 to Pin 6 to eliminate power fault alarm. 2.10 Grounding Note Grounding and wire routing help limit the effects of noise due to electromagnetic interference (EMI). Run the ground connection from the ground screw to the grounding surface prior to connecting devices.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 3. Mounting Installation 3.1 DIN-Rail Mounting The DIN-Rail is pre-installed on the industrial Ethernet switch from the factory. If the DIN-Rail is not on the industrial Ethernet switch, please see Figure 3.1 to learn how to install the DINRail on the switch. Figure 3.1 The Rear Side of the Switch and DIN-Rail Bracket Follow the steps below to learn how to hang the industrial Ethernet switch. 1.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 3.2 Wall Mounting Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as shown below in Figure 3.4. Caution: “Wall” means industrial control panel wall 1. Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws. 2. Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch. 3.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 4. Hardware Installation 4.1 Installation Steps This section will explain how to install Antaira’s LMX-1002G-SFP series: 10-port industrial gigabit managed Ethernet switches with 8*10/100/1000Tx and 2*100/1000 SFP slots for fiber. Caution: This device is intended for use indoor and at altitudes up to 2000 meters. Caution: The device is intended to be installed in an industrial control enclosure and panel.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 Do not under any circumstance insert foreign objects of any kind into the heat dissipation holes located in the different faces of the device. This may not only harm the internal layout, but might cause harm to user as well. Do not under any circumstance open the device for any reason. Please contact your dealer for any repair needed or follow the instructions within the manual.
Antaira Technologies - Industrial Ethernet Switches LMX-1002G-SFP Series Hardware Manual V1.3 Port Interface Fiber Port 2*100/1000 dual rate SFP Slots for fiber Wavelength Refer to SFP Key Module 1*RS232 in RJ45 connector with console cable, 115.2Kbps, Serial Console Port 8,N,1 Configuration Backup Port 1*USB 2.0 Overload Current Present Power Reverse polarity Present CPU Watch Dog Present Protection 10Base-T: 2-pair UTP/STP Cat. 3, 4, 5 cable; 100Base-TX: 2pair UTP/STP Cat. 5 cable.
