Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series User Manual V1.0 LMX-0804G-SFP Series 8-Port Industrial Gigabit Managed Ethernet Switches with 4*10/100/1000Tx, 4*100/1000 SFP Slots Version 1.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 © Copyright 2018 Antaira Technologies, LLC All Rights Reserved This document contains information, which is protected by copyright. Reproduction, adaptation or translation without prior permission is prohibited, except as allowed under the copyright laws.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 FCC Warning This equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 Table of Contents 1. Introduction ................................................................. 1 1.1 Product Overview 1 1.2 Product Software Features 1 1.3 Product Hardware Features 2 1.4 Package Contents 3 1.5 Safety Precaution 3 2. Hardware Description ................................................. 4 2.1 Physical Dimensions 4 2.2 Front Panel 5 2.3 Top View 5 2.4 LED Indicators 6 2.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 1. Introduction All Antaira industrial managed switches come with a pre-installed “user-friendly” web console interface, which allows users to easily configure and manage the units, whether one is using a serial console and command line interface (CLI) commands like Telnet, SSH, HTTP (Web GUI) or simple network management protocols (SNMP). 1.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 1.4 Package Contents 1– LMX-0804G-SFP series: 8-port industrial gigabit managed Ethernet switch, with 4*10/100/1000Tx ports and 4*100/1000 SFP slots 1-Product CD DIN Rail Kit & 2-W all mounting brackets and screws 1-RJ45 to DB9 Serial Console cable 1-DC cable –18 AWG & DC jack 5.5x2.1mm 1.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 2. Hardware Description 2.1 Physical Dimensions Figure 2.1, below, shows the physical dimensions of Antaira’s LMX-0804G-SFP series: 8-port industrial gigabit managed Ethernet switches with 4*10/100/1000Tx RJ45 Ethernet ports and 4*100/1000 SFP fiber slots. (W x D x H) is 54mm x 99mm x 142mm Figure 2.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 2.2 Front Panel The front panel of the LMX-0804G-SFP series industrial gigabit managed Ethernet switch is shown below in Figure 2.2.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 2.4 LED Indicators There are LED light indicators located on the front panel of the industrial Ethernet switch that display the power status and network status. Each LED indicator has a different color and has its own specific meaning, see below in Table 2.1.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 Seconds Function 1 Save running configuration to USB 4-6 Reboot the switch 7 or more Restore factory default Table 2.2 – Reset Button Functions 2.6 Ethernet Ports RJ-45 Ports RJ-45 Ports (Auto MDI/MDIX): The RJ-45 ports are auto-sensing for 10Base-T, 100Base-TX, or 1000Base-T connections.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 The following figures show the cabling schematics for straight-through and crossover. Figure 2.4 Straight-Through Cable Schematic Figure 2.5 Crossover Cable Schematic 2.7 Cabling Use the four twisted-pair, category 5e, or the above cabling for the RJ-45 port connections. The cable between the switch and the link partner (switch, hub, workstation, etc.) must be less than 100 meters (328 ft.) in length. 2.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 2.9 Wiring the Fault Alarm Contact The fault alarm contact is in the middle of the terminal block connector as the picture shows below in Figure 2.8. By inserting the wires, it will detect the fault status including power failure or port link failure (managed industrial switch only) and form a normally open circuit. An application example for the Figure 2.8 – fault alarm contact is shown in Figure 2.8.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 3. Mounting Installation 3.1 DIN-Rail Mounting The DIN-Rail is pre-installed on the industrial Ethernet switch from the factory. If the DINRail is not on the industrial Ethernet switch, please see Figure 3.1 to learn how to install the DIN-Rail on the switch. Figure 3.1 The Rear Side of the Switch and DIN-Rail Bracket Follow the steps below to learn how to hang the industrial Ethernet switch. 1.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 3.2 Wall Mounting Follow the steps below to mount the industrial Ethernet switch using the wall mounting bracket as shown below in Figure 3.4. Caution: “Wall” means industrial control panel wall 1. Remove the DIN-Rail bracket from the industrial Ethernet switch by loosening the screws. 2. Place the wall mounting brackets on the top and bottom of the industrial Ethernet switch. 3.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 4. Hardware Installation 4.1 Installation Steps This section will explain how to install Antaira’s LMX-0804G-SFP series: 8-port industrial gigabit managed Ethernet switches with 4*10/100/1000Tx ports and 4*100/1000 SFP fiber slots. Caution: This device is intended for use indoor and at altitudes up to 2000 meters. Caution: The device is intended to be installed in an industrial control enclosure and panel.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 Voltage/Power lines should be properly insulated as well as other cables. Be careful when handling them so as to not trip over. Do not under any circumstance insert foreign objects of any kind into the heat dissipation holes located in the different faces of the device. This may not only harm the internal layout, but might cause harm to user as well.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 IEEE 802.3x for full duplex mode, back pressure for half duplex Flow Control mode VLAN Groups 1 ~ 4094 IGMP Groups Up to 256 Ethernet (RJ45) Port Port Interface Fiber Port Serial Console Port Protection 4*10/100/1000BaseTx auto negotiation speed, Full/Half duplex mode, and auto MDI/MDI-X connection 4*100/1000 dual rate SFP slots for fiber 1*RS232 in RJ45 connector with console cable, 115.
Antaira Technologies - Industrial Ethernet Switches LMX-0804G-SFP Series Hardware Manual V1.1 Antaira Customer Service and Support (Antaira US Headquarter) + 844268-2472 (Antaira Europe Office) + 4822-862-88-81 (Antaira Asia Office) + 8862-2218-9733 Please report any problems to Antaira: www.antaira.com / support@antaira.com www.antaira.eu / info@antaira.eu www.antaira.com.tw / info@antaira.com.tw Any changes to this material will be announced on the Antaira website.
