User Manual
ENGLISH
ANTMIX Series | User manual
12
13
SERIES
User manual | ANTMIX Series
BOARDS INSTALLATION
The installation is very simple, but if you have no experience, contact a specialized service center.
WARNING: for your safety, operate turning off the mixer and unplugging the appliance from the mains socket.
With a flat-headed screwdriver, press gently under the plastic cover and pry up the right side to remove it carefully. (Fig.1)
To install the optional MPX 1624 or BTX 1624 card, connect the 5-pin connector cable to the respective 5-pin connector
on the printed circuit board of the mixer. (Fig.2). At this point it is sufcient to hook the optional module in the appropriate
housing and take advantage of the new functions.
BLUETOOTH
®
MODULE - BTX 1624
Activate the Bluetooth
®
interface of your device and press the PAIR button of the board. The source device should
recognize the board as BT 4.0 and synchronize automatically.
In the mixer, press the 2TK TO MAIN MIX selector, then gradually raise the 2TK LEVEL knob and the MAIN MIX fader
until you reach the desired volume.
You can also control the volume from the Bluetooth
®
card itself, using the VOL- and VOL+ keys, using the
and PAUSE the key you can choose the track to listen to or pause it
MP3 PLAYER MODULE - MPX 1624
In a USB stick, load all the tracks you want (up to 32Gb), even in multiple folders. Insert the stick into the USB port of
the optional board by simply pressing the PUSH & HOLD button for 2 seconds to start playing the ladder from the rst
track. The display will alternately show the number of the le and its folder.
To listen to the previous song just press
, while to listen to following track press
;
holding down the keys you
can change the folder. The
key pause or resume the song, if you press stop playback will be totally stopped.
If you press more times the key, you can choose random play, a single song play or all tracks play.
In the mixer, please press the 2TK TO MAIN MIX selector, then gradually raise the 2TK LEVEL knob and the MAIN MIX
fader until you reach the desired listening volume.
3.1.5 | OPTIONAL BLUETOOTH
®
& MP3 PLAYER BOARDS 4 | TROUBLESHOOTING
PROBLEM LED SOLUTION
No sound or very
low sound level
Power LED turned off.
Make sure the device is properly connected to the mains
outlet.
Power LED turned on, but MAIN MIX low. Raise MAIN MIX level.
Power LED turned on, MASTER VOL raised, but
MUTE button depressed.
Raise MUTE button.
Power LED turned on, MASTER VOL raised, but
input channel LEVEL low.
Check connections between sources and mixer. Raise
channel LEVEL.
Power LED turned on, MASTER VOL raised,
LEVEL raised, but +48V off.
Activate +48V power for microphones deserving it.
Power LED turned on, MAIN MIX raised but,
signal addressed to GR1-2 or GR3-4 are not
addressed to MAIN MIX
Press the L-R button over GR1, GR2, GR3 and/or GR4
faders
No effects heard
DFX MUTE activate
Turn off the DFX MUTE button, anc check send levels of all
the channels.
DFX MUTE deactivated
Check the levels of DFX RETURN as well as GR1-2, GR3-4
and MAIN MIX assign buttons.
No FX signal in
monitors
DFX MUTE deactivated Check DFX TO AUX 1 and DFX TO AUX 2 knobs levels
Distortion PEAK LED lit.
Reduce the level of the inputs and/or MAIN MIX
Check you haven't connected a line signal into a MIC
socket..
Confused sound
Make sure you haven't simultaneously activated more
sound sources in the same channel
Check if you activated microphones LOW CUT lter
Check that LINE/USB selectors of the stereo channel 15-16
(ANTMIX 16FX USB) or 23-24 are not addressed to MAIN
MIX while you're listening to USB signal via MAIN MIX.
Recorded signal is
not heard
Check that LINE/USB selectors of the stereo channel
15-16 (ANTMIX 16FX USB) or 23-24(ANTMIX 24FX USB)
is pressed and that PLAYBACK selector is addressed to
desired output (MAIN or GR1-2)
No recording
Check that PLAYBACK selector is addressed to desired
output (MAIN or GR1-2) and that desired signal are
addressed to the right destination.
Loop in recording
LINE/USB stereo channel 15-16 (ANTMIX 16FX USB) or
23-24 (ANTMIX 24FX USB) is pressed and the PLAYBACK
selector is addressed to the wrong oputput (MAIN or
GR1-2)
Fig.1 Fig.2