Manual

2322
Unloading
It is only possible to remove a pellet from
the action by firing it off which should only
be done by firing it into a bullet trap.
Observe the safety regulations with regard
to the safe handling of rifles.
Trigger
Warning:
Your ANSCHÜTZ target rifle offers you a
versatility of individual adjusting properties.
Please make sure that your rifle always is
unloaded when carrying out adjustments.
Trigger adjustments
1. Trigger weight
Adjust the trigger weight with set screw
No. 2:
•if you turn it to the right:
trigger weight is increased (+)
•if you turn it to the left:
trigger weight is decreased (-)
Trigger weight and first stage weight
depend on each other with regard to the
mechanic mechanism. If one of them is
changed there will always be a corres-
ponding change of the other as well.
Assembly, fitting the
ANSCHÜTZ barreled action
The stock and the barreled action are
packed separately for shipment and need
to be assembled. However, do not do this
until you have followed all the procedures
listed below.
•Wipe away excess surface oil.
•Insert the barreled action into the stock.
•Screw in bedding screws (two) with
enclosed Allen wrench Model No. 4406
(Order No. 710.6301) and tighten them
alternately and uniformly. For correct ad-
justments we recommend our torque
wrench model No. 4405 (Order No.
700.6180), which is to be adjusted to
5 Nm (= 50 cmkp) for wood stocks and
to 6 Nm (60 cmkp) for aluminum stocks.
•Pull a cleaning patch through the barrel
from the chamber towards the muzzle.
After the first assembly there might be a
warping of the wood. We would therefore
recommend to loosen and tighten the
bedding screws again after some time.
Cocking, loading and safety
operation
•Pull back the action to the stop with the
cocking handle. Subsequently pull it up-
wards and lock it in the groove. The action
is now in the magazine loading position.
•Insert the magazine from the right side to
the stop. The magazine cap now shows
in the direction of the shooter, the push
knob to the top.
•Remove the action from the catch position
with the cock handle by turning it down-
wards. Then put your thumb on the thumb
rest. Push the action forward into the catch
position with your thumb. The biathlon rifle
is now ready for shooting.
•To repeat pull the action back with the
cock handle until you hear that it catches,
then close with thumb rest as described
above.
Note:
Only close the action with your thumb via
the thumb rest. Do not use the cock handle
as the action might get jammed.
Attention:
The safety lever must latch properly so that
the ”F“ is covered in the ”safe“ position and
the ”S“ is covered in the ”fire“ position. The
lever must never be situated between the two.
Do not store the rifle when it is cocked.
Remove the compressed air cylinder before
storing your rifle (also see chapter
”Compressed Air Cylinder/Handling”!).
Summer Biathlon Match Rifle
2027 Compressed Air
Technical Data:
Caliber: 4.5 mm
Barrel length: 61 cm/24.01"
Rifling: 42 cm/16.5"
Total length: 106 cm/41.7"
Length of
barreled action: 74 cm/29.1"
Weight: 4.5 kg/9.9 lbs
Version: Repeater
Check the tight fit of the screws before every
shooting.
Only use diabolo pellets in the caliber of
your air rifle, no bolts or other foreign
materials.
re
Magazine
•Remove the magazine cap and pull the
sliding knob to the right stop.
•Keep the lever in this position and insert
a pellet with the cup up into the groove.
•Release the sliding knob, put the cap on
and catch into the referring postion. The
magazine is now loaded.
5-shot magazine:
Identification: The sliding knob is not
notched.
1-shot magazine:
Identification: The sliding knob is notched.