Portable Generator User Manual

ManualsBrandsAnritsu ManualsElectronic KeyboardMG3700A

MX370x series software

MG3700A Vector Signal Generator

Superior Expandability Supporting A Wide Variety Of Communication Systems

MX3700xxA Waveform pattern

MX3701xxA IQproducer

*MX370X_E_050127 1/28/05 8:50 AM Page 1

Summary of content (36 pages)

PAGE 1
*MX370X_E_050127 1/28/05 8:50 AM Page 1 MG3700A Vector Signal Generator MX370x series software MX3700xxA Waveform pattern MX3701xxA IQproducer Superior Expandability Supporting A Wide Variety Of Communication Systems
PAGE 2
*MX370X_E_050127 1/28/05 8:50 AM Page 2 MX370x series software The MG3700A Vector Signal Generator (hereafter referred to as “MG3700A”) is a signal generator that integrates a 160-MHz high-speed ARB baseband generator. With features that include a broadband vector modulation bandwidth and large-capacity ARB memory, it supports digital modulation signals for a variety of communication systems.
PAGE 3
*MX370X_E_050127 1/28/05 8:50 AM Page 3 The standard waveform patterns are saved on the MG3700A hard disk. Waveform patterns are transferred from the HDD to ARB memory.
PAGE 4
*MX370X_E_050127 1/28/05 8:50 AM Page 4 W-CDMA waveform pattern Standard ■ W-CDMA waveform pattern: •For testing receivers and performance of UE (TS 25.101 DL RMC 12.
PAGE 5
*MX370X_E_050127 1/28/05 8:50 AM Page 5 W-CDMA waveform pattern Standard •W-CDMA waveform pattern list Waveform pattern UL_RMC_12_2kbps UL_RMC_12_2kbps_ACS UL_RMC_64kbps UL_RMC_144kbps UL_RMC_384kbps UL_AMR_TFCS1 UL_AMR_TFCS2 UL_AMR_TFCS3 UL_ISDN UL_64kbps_Packet UL_Interfere UL_RMC_12_2kbps_TX P_CCPCH DL_RMC_12_2kbps_RX DL_RMC_12_2kbps_ACS DL_RMC_12_2kbps DL_RMC_12_2kbps_MIL DL_RMC_64kbps DL_RMC_144kbps DL_RMC_384kbps DL_AMR_TFCS1 DL_AMR_TFCS2 DL_AMR_TFCS3 DL_ISDN DL_384kbps_Packet DL_Interfere DL_CPI
PAGE 6
*MX370X_E_050127 1/28/05 8:50 AM Page 6 W-CDMA waveform pattern Standard ■ ACPR: The adjacent channel leakage power ratio of a Vector Signal Generator is an important factor in device distortion testing and receiver interference testing.
PAGE 7
*MX370X_E_050127 1/28/05 8:50 AM Page 7 W-CDMA waveform pattern Standard ■ AWGN (Additive White Gaussian Noise) Supports Dynamic Range Test When performing the receiver dynamic range test specified by 3GPP, AWGN with a W-CDMA modulation signal is required. Either of the AWGN waveform patterns AWGN_3_84MHz_x2 or AWGN_3_84MHz_x1_5, which are stored on the MG3700A internal hard disk, can be used for an AWGN signal.
PAGE 8
*MX370X_E_050127 1/28/05 8:50 AM Page 8 CDMA2000 1xEV-DO waveform pattern Standard ■ CDMA2000 1xEV-DO waveform pattern: •Access terminal (AT) receiver test CDMA2000 1xEV-DO forward Base band filter: IS-95SPEC +EQ Data: PN15fix∗ (excluding FWD-Idle) FWD_38_4kbps_16slot FWD_76_8kbps_8slot FWD_153_6kbps_4slot FWD_307_2kbps_2slot FWD_614_4kbps_1slot FWD_307_2kbps_4slot FWD_614_4kbps_2slot FWD_1228_8kbps_1slot FWD_921_6kbps_2slot FWD_1843_2kbps_1slot FWD_1228_8kbps_2slot FWD_2457_6kbps_1slot FWD_Idle The
PAGE 9
*MX370X_E_050127 1/28/05 8:50 AM Page 9 CDMA2000 1xEV-DO waveform pattern Standard •Access network (AN) receiver test GPP2 C.S0032 standard receiver tests (PER: Packet Error Rate) can be performed by selecting a reverse signal pattern required for testing the AN. Since access terminal simulator protocols are not supported, an external controller must be used to control the AN and calculate PER.
PAGE 10
*MX370X_E_050127 1/28/05 8:50 AM Page 10 CDMA2000 waveform pattern Standard ■ CDMA2000 waveform pattern: The CDMA2000 waveform patterns listed in the table below are provided on the MG3700A internal hard disk. CDMA2000 modulation signals specified in 3GPP2 C.S0002-0-2 can be output by selecting one of these CDMA2000 waveform patterns. Since reverse channel signals are output by channel coding (convolutional coding, etc.
PAGE 11
*MX370X_E_050127 1/28/05 8:50 AM Page 11 GSM/EDGE waveform pattern Standard ■ GSM/EDGE waveform pattern: The GSM/EDGE waveform patterns listed in the table below are provided on the MG3700A internal hard disk. The signals suitable for testing receivers and for managing device evaluation in a GSM/EDGE system can be output by selecting one of these GSM/EDGE waveform patterns. • GMSK_PN9, 8PSK_PN9 PN9 data is inserted into the entire area of the slots, except the guard.
PAGE 12
*MX370X_E_050127 1/28/05 8:51 AM Page 12 PHS waveform pattern Standard ■ PHS waveform pattern: The PHS waveform patterns listed in the table below are provided on the MG3700A internal hard disk. The signals for testing CS (base station) and PS (mobile station) receivers, which are specified in RCR STD-28, can be output by selecting one of these PHS waveform patterns, without setting any complex RCR STD-28 parameters.
PAGE 13
*MX370X_E_050127 1/28/05 8:51 AM Page 13 PDC waveform pattern Standard ■ PDC waveform pattern: The waveform patterns for the wanted signals/interfering signals required to execute transmission/reception tests as specified in ARIB STD-27 are provided on the MG3700A internal hard disk. Modulation signals conforming to the standard can be output without any options (Note: Check the parameters listed on the next page in advance).
PAGE 14
*MX370X_E_050127 1/28/05 8:51 AM Page 14 PDC Packet waveform pattern Standard ■ PDC Packet waveform pattern: The four types of waveform patterns listed in the table below are provided on the MG3700A internal hard disk. The signals for testing base station and mobile station receivers for UPCH communications, which are specified in RCR STD-27, can be output by selecting one of these waveform patterns, without setting any complex RCR STD-27 parameters.
PAGE 15
*MX370X_E_050127 1/28/05 8:51 AM Page 15 WLAN waveform pattern Standard ■ WLAN waveform pattern: The WLAN (IEEE802.11a/b/g) waveform patterns listed in the table below are provided on the MG3700A internal hard disk. The signals for testing the receiver/transmitter of a terminal or module can be output by selecting one of these WLAN waveform patterns. Example of selecting waveform pattern • IEEE_802.
PAGE 16
*MX370X_E_050127 1/28/05 8:51 AM Page 16 AWGN waveform pattern Standard ■ AWGN waveform pattern: The Additive White Gaussian Noise (AWGN) waveform patterns listed in the table below are provided on the MG3700A internal hard disk. The signals for testing the receiver/transmitter of a terminal or module can be output by selecting one of these AWGN waveform patterns.
PAGE 17
*MX370X_E_050127 1/28/05 8:51 AM Page 17 AWGN waveform pattern Standard ■ With the waveform combine function, a single MG3700A outputs a signal that is the addition (such as modulation signal + AWGN) of the wanted signal and interfering signal: The MG3700A has ARB memory that consists of two memory areas, each allowing one waveform pattern to be set. The addition of the signals from the two memories, as well as the signal for either one, can be output.
PAGE 18
*MX370X_E_050127 1/28/05 8:51 AM Page 18 MX370001A TD-SCDMA waveform pattern Optional ■ TD-SCDMA waveform pattern: ■ Simple operation and high speed signal pattern change: The signals corresponding to the 3GPP 1.28Mcps TDD options can be output by installing the MX370001A TD-SCDMA waveform pattern on the MG3700A.
PAGE 19
*MX370X_E_050127 1/28/05 8:51 AM Page 19 MX370001A TD-SCDMA waveform pattern Optional • Waveform patterns for evaluating BS receivers Target of test Test signal Waveform patterns Test rmc12_2k_bs_ul RS / Min. Input Lev./ Dynamic range /ACS / Blocking / Rx IM BS Receive Test (UL) BS BS-UL RMC rmc12k_ocns_bs_ul rmc64k_ocns_bs_ul Performance Req. Performance Req. rmc144k_bs_ul rmc384k_bs_ul Performance Req. Performance Req.
PAGE 20
*MX370X_E_050127 1/28/05 8:51 AM Page 20 MX370001A TD-SCDMA waveform pattern Optional ■ Frame configuration •UL-RMC12.2 kbps: For BS receiver test (Uplink): TS-25.142: BS UL reference measurement channel p132, A2.1.2, 1.28 MCps, SF = 8 Test items: 7.2 Reference sensitivity level / 7.3 Dynamic range / 7.4 Adjacent Channel Selectivity (ACS) / 7.5 Blocking characteristics / 7.
PAGE 21
*MX370X_E_050127 1/28/05 8:51 AM Page 21 MX370002A Public radio system waveform pattern Optional ■ Public radio system waveform pattern: The signals for testing the receiver/tester specified in the ARIB standards can be output by selecting a waveform pattern loaded from the MG3700A internal hard disk to the largecapacity ARB memory, without setting any complex ARIB standard parameters. The TCH/CCH pattern, PN9 pattern, and PN15 continuous modulation pattern can be switched quickly.
PAGE 22
*MX370X_E_050127 1/28/05 8:51 AM Page 22 MX370002A Public radio system waveform pattern Optional •ARIB STD-T79 •ARIB STD-T61 frame configuration Waveform pattern Uplink / Downlink UpLink Uplink / Downlink 0, x, x, x DownLink 1 Uplink / Downlink 0, x, x, x DownLink 4 Uplink / Downlink 0, 1, 2, 3 Direct Uplink / Downlink 1, x, x, x The uplink/downlink frames both generate data in cycles of 40 ms defined as a basic frame length.
PAGE 23
*MX370X_E_050127 1/28/05 8:51 AM Page 23 MX370002A Public radio system waveform pattern Optional ■ Signal formats in each system • Downlink R 6 •RCR STD-39, slot format The signal formats in uplink/downlink are as follows.
PAGE 24
*MX370X_E_050127 1/28/05 8:52 AM Page 24 MX370101A HSDPA IQproducer Optional ■ HSDPA IQproducer: • Downlink Settings: Various parameters conforming to standards can be set for downlink (for details, refer to the “Downlink parameter setting range” table shown later). The Downlink Easy Setup function provides the items for the HSDPA Fixed Reference Channel (FRC) specified in 3GPP TS25.101 and the Reference Measurement Channel (RMC) specified in 3GPP TS25.101, TS25.104.
PAGE 25
*MX370X_E_050127 1/28/05 8:53 AM Page 25 MX370101A HSDPA IQproducer Optional • Downlink Main screen: • Uplink Main screen: 25
PAGE 26
*MX370X_E_050127 1/28/05 8:53 AM Page 26 MX370101A HSDPA IQproducer Optional • Downlink parameter setting range: Display Setting range Scrambling Code CPICH P-CCPCH PICH DPCH 0 to 8191 ON/OFF ON or OFF Power –40.00 to 0.00 [dB], Resolution 0.01 dB ON/OFF ON or OFF Power –40.00 to 0.00 [dB], Resolution 0.01 dB ON/OFF ON or OFF Power –40.00 to 0.00 [dB], Resolution 0.01 dB Channelization Code 0 to 255 ON/OFF ON or OFF Power –40.00 to 0.00 [dB], Resolution 0.
PAGE 27
*MX370X_E_050127 1/28/05 8:53 AM Page 27 MX370101A HSDPA IQproducer Optional • Uplink parameter setting range: Display Setting range Scrambling Code 0 to 16777215 Channel ON/OFF UL-DPCCH, UL-DPDCH ON or OFF Power 0 to –40.00 dB RMC 12.2 kbps / RMC 64 kbps / RMC 144 kbps / RMC 384 Data HS-DPCCH DPCH Edit kbps / AMR1 / AMR2 / AMR3 / ISDN / 64 kbps Packet ON/OFF HS-DPCCH ON or OFF Timing Offset 0 to 149 ACK Power 0 to –40.00 dB NACK Power 0 to –40.00 dB CQI Power 0 to –40.
PAGE 28
*MX370X_E_050127 1/28/05 8:53 AM Page 28 MX370102A TDMA IQproducer Optional ■ TDMA IQproducer: • IQproducer™ operating environment The MX370102A TDMA IQproducer“ is GUI-driven PC application software used to set up the parameters and generate waveform patterns according to the TDMA system. The generated waveform patterns are downloaded to the MG3700A, and used to output TDMA Modulation baseband signals and RF signals with the ARB generation function of the MG3700A.
PAGE 29
*MX370X_E_050127 1/28/05 8:54 AM Page 29 MX370102A TDMA IQproducer Optional • Parameter setting items list: Parameter setting sheet Setting items Modulation Burst Continuous No Format ✓ ✓ ✓ ✓ ✓ Frame — Slot ✓ ✓ — Field ✓ ✓ — Data — — ✓ Filter ✓ ✓ ✓ Pattern Name ✓ ✓ ✓ • Parameter setting items list: Items Modulation Frame Display Modulation system Symbol Rate Symbol rate 1ksps to 40Msps (Specified in increments of 1 sps.
PAGE 30
*MX370X_E_050127 1/28/05 8:54 AM Page 30 MX370102A TDMA IQproducer Optional • Graph: • Ramp field Setting range: Modulation Type This function displays a generated waveform pattern in a CCDF or FFT graph on the PC. It is useful to check/review the waveform pattern in a graph before transferring it to the MG3700A.
PAGE 31
*MX370X_E_050127 1/28/05 8:54 AM Page 31 MX370103A CDMA2000 1xEV-DO IQproducer Optional ■ CDMA2000 1xEV-DO IQproducer: • IQproducer™ operating environment The MX370103A CDMA2000 1xEV-DO IQproducer is GUI-driven PC application software used to set up the parameters and generate waveform patterns according to the CDMA2000 1xEV-DO system (1xEV-DO forward and 1xEV-DO Reverse).
PAGE 32
*MX370X_E_050127 1/28/05 8:54 AM Page 32 MX370103A CDMA2000 1xEV-DO IQproducer Optional • 1xEV-DO forward setting range [Carrier Edit sheet] On the Carrier Edit sheet, set up the Modulation parameters for the single carriers (associated with carrier numbers 1 to 9) that constitute the multi-carrier.
PAGE 33
*MX370X_E_050127 1/28/05 8:54 AM Page 33 MX370103A CDMA2000 1xEV-DO IQproducer Optional • 1xEV-DO Reverse Setting range: Display Over Sampling Carrier On/Off Description Ratio of the waveform pattern sampling rate and the chip rate Set the carrier On/Off. It is “On” when checked. Long Code Mask Set the I and Q long code masks. MQ is set automatically when MI is set by a user. Power Frequency Offset Phase Offset DRC CH On/Off DRC CH Gain Set the power of carrier.
PAGE 34
*MX370X_E_050127 1/28/05 8:54 AM Page 34 MX370103A CDMA2000 1xEV-DO IQproducer Optional ■ Parameter save/recall: The numeric values and settings for each item can be saved in a parameter file. Type the desired name in the [file name] text box and then click the [Save] button to save the parameter file. A parameter file can be recalled. Click the desired parameter file from the file list and then click the [Open] button.
PAGE 35
*MX370X_E_050127 1/28/05 8:54 AM Page 35 Ordering information Please specify model/order number, name, and quantity when ordering. Model/Order No. Name Remarks MG3700A — Mainframe — Vector Signal Generator J0017F J1276 P0020 J1254 Z0742 — Standard accessories — Power cord, 2.
PAGE 36
*MX370X_E_050127 1/28/05 8:54 AM Page 36 Specifications are subject to change without notice. ANRITSU CORPORATION 1800 Onna, Atsugi-shi, Kanagawa, 243-8555 Japan Phone: +81-46-223-1111 Fax: +81-46-296-1264 • U.S.A. ANRITSU COMPANY TX OFFICE SALES AND SERVICE 1155 East Collins Blvd., Richardson, TX 75081, U.S.A. Toll Free: 1-800-ANRITSU (267-4878) Phone: +1- 972-644-1777 Fax: +1-972-644-3416 • Canada ANRITSU ELECTRONICS LTD.