User Manual
Table Of Contents
- Intr
- 1.Product features overv
- 1.1Product introduction
- 1.2 Product parameters.
- 1.3Functional features
- 2.Operating instructions
- 2.1The front panel expla
- 2.2Rear Panel Interface
- 2.3The mouse operation i
- 2.4Input method instruct
- 2.5The remote control ope
- 2.6Interface specificatio
- 2.6.1Interface elements s
- 2.6.2Commonly used butto
- 2.7Menu description
- 3.Installation and conne
- 3.1Installation Notes
- 3.2Prepare before instal
- 3.3The camera placed in the
- 4.System function introdu
- 4.1Starting up/Login/Log
- 4.1.1 Starting up
- 4.1.2 Login
- 4.1.3 Logout
- 4.1.4 Restart
- 4.1.5 Close the screen o
- 4.1.6 Turn off
- 4.2Boot wizard
- 4.3 Video management
- 4.3.1 Search device
- 4.3.2 Add device
- 4.3.3 Advanced setup
- 4.3.4.Delete device
- 4.3.5Repeater function
- 4.3.6Edit channel
- 4.3.7Encoding setup
- 4.3.8Code stream value
- 4.3.9 Channels in detail
- 4.3.10 Channel OSD
- 4.3.11 Camera
- 4.4 Network Setup
- 4.4.1.Network Setup
- 4.4.2.Dynamic DNS
- 4.4.3.FTP26
- 4.4.4.E-Mail
- 4.4.5.PPPoE
- 4.4.6.3G
- 4.4.7.Wireless setup
- 4.5 PTZ setup
- 4.5.1 PTZ parameter setu
- 4.5.2 PTZ control operat
- 4.5.3 PTZ automatic crui
- 4.6 Video
- 4.6.1 Manual video
- 4.6.2 Timing video
- 4.6.3 The motion detecti
- 4.6.4 Alarm video
- 4.7 Video playback
- 4.7.1 Quick playback
- 4.7.2 Regular playback
- 4.8Video backup
- 4.9 Alarm
- 4.9.1Motion detecting al
- 4.9.2Video loss alarm
- 4.10 General setup
- 4.10.1General setup
- 4.10.2Timeset
- 4.10.3Screen setup
- 4.10.4Hard disk setup
- 4.11Device maintenance a
- 4.11.1 System information
- 4.11.2 User management
- 4.11.3 Restore the factor
- 4.11.4 System maintenanc
- 4.11.5 Software upgrade
- 4.11.6 IPC maintenance
- 5WEB access
- 5.1 Introduction
- 5.2 LAN Access
- 5.2.1 Login
- 5.2.2 Preview
- 5.2.3 Playback
- 5.2.4 Configuration
- 5.3 E-seenet access
- 5.3.1 E-seenet ID login
- 5.3.2 The user name logi
- 6.Mobile terminal access
- 7. Appendix
- 7.1Hard disk capacity un
- 7.2Video required capaci
- Introduction
- 1.Product features overview
- 2.Operation explanation
- 3.Installation and connection
- 4.System function introduction
- 4.1Starting up / login / logout / restart / close
- 4.2Boot wizard
- 4.3 Video management
- 4.3.1 Search for device
- 4.3.2 Add device
- 1. Code matching instructions：
- 2:Code matching methods：
- 4.3.3 Advanced setups
- 4.3.4.Delete device
- 4.3.5 Repeater setup
- 4.3.6.Edit Channel
- 4.3.7.Encoding setup
- 4.3.8 Stream value
- 4.3.9 Channel details
- 2、Click Refresh, you can search the camera in curr
- 4.3.10 Channel OSD
- 3, Select the display setup, enter the location of
- 4.3.11 Camera
- 4.4 Network setup
- Click Reset to restore the information of the wire
- 4.5 PTZ setup
- 4.6 Recording
- 4.7 Video playback
- 4.8 Video backup
- 4.9 Alarm
- 4.10 General Setups
- 4.11 Equipment maintenance and management
- 5WEB Access
- 6.Mobile access
- 7.Appendix
Wireless NVR Kit Manual
33
If you need to set motion detection for other channels, repeat the above steps.
The default sensitivity for video detection is "higher".
4.6.4 Alarm recording
Function explanation：Turn on the alarm recording function, the system will record when detecting the alarm input.
Steps：
1, Right click on the main interface and select System Setup in the shortcut menu.
2, In the "System Setup" interface, select the alarm setup for the recording schedule. As shown below：
3, Select the alarm type, alarm serial number and alarm area, trigger the type of alarm, click "Add". Waiting 30
seconds, there will prompt "add success".
4, After adding successfully, you can set the alarm continuity, video channels and video alarm mode.
5, Select the channel that needs to trigger the recording.
6, For the alarm recording plan configuration, refer to "4.6.2 Recording Plan Configuration Method of Timed
Recording", and check the "Alarm" checking box.
7, Click the "OK" button to save the alarm recording setup.
Explanation
If you need to set the alarm input of other network cameras, please repeat the above steps.
If the other alarm inputs are consistent with this alarm input setup, select the channel and click the "Copy to"
button.
4.7 Video playback
4.7.1 Fast playback
Function explanation：Open the fast playback function, the user can quickly retrieve the latest video data.