User Manual
Table Of Contents
- Intr
- 1.Product features overv
- 1.1Product introduction
- 1.2 Product parameters.
- 1.3Functional features
- 2.Operating instructions
- 2.1The front panel expla
- 2.2Rear Panel Interface
- 2.3The mouse operation i
- 2.4Input method instruct
- 2.5The remote control ope
- 2.6Interface specificatio
- 2.6.1Interface elements s
- 2.6.2Commonly used butto
- 2.7Menu description
- 3.Installation and conne
- 3.1Installation Notes
- 3.2Prepare before instal
- 3.3The camera placed in the
- 4.System function introdu
- 4.1Starting up/Login/Log
- 4.1.1 Starting up
- 4.1.2 Login
- 4.1.3 Logout
- 4.1.4 Restart
- 4.1.5 Close the screen o
- 4.1.6 Turn off
- 4.2Boot wizard
- 4.3 Video management
- 4.3.1 Search device
- 4.3.2 Add device
- 4.3.3 Advanced setup
- 4.3.4.Delete device
- 4.3.5Repeater function
- 4.3.6Edit channel
- 4.3.7Encoding setup
- 4.3.8Code stream value
- 4.3.9 Channels in detail
- 4.3.10 Channel OSD
- 4.3.11 Camera
- 4.4 Network Setup
- 4.4.1.Network Setup
- 4.4.2.Dynamic DNS
- 4.4.3.FTP26
- 4.4.4.E-Mail
- 4.4.5.PPPoE
- 4.4.6.3G
- 4.4.7.Wireless setup
- 4.5 PTZ setup
- 4.5.1 PTZ parameter setu
- 4.5.2 PTZ control operat
- 4.5.3 PTZ automatic crui
- 4.6 Video
- 4.6.1 Manual video
- 4.6.2 Timing video
- 4.6.3 The motion detecti
- 4.6.4 Alarm video
- 4.7 Video playback
- 4.7.1 Quick playback
- 4.7.2 Regular playback
- 4.8Video backup
- 4.9 Alarm
- 4.9.1Motion detecting al
- 4.9.2Video loss alarm
- 4.10 General setup
- 4.10.1General setup
- 4.10.2Timeset
- 4.10.3Screen setup
- 4.10.4Hard disk setup
- 4.11Device maintenance a
- 4.11.1 System information
- 4.11.2 User management
- 4.11.3 Restore the factor
- 4.11.4 System maintenanc
- 4.11.5 Software upgrade
- 4.11.6 IPC maintenance
- 5WEB access
- 5.1 Introduction
- 5.2 LAN Access
- 5.2.1 Login
- 5.2.2 Preview
- 5.2.3 Playback
- 5.2.4 Configuration
- 5.3 E-seenet access
- 5.3.1 E-seenet ID login
- 5.3.2 The user name logi
- 6.Mobile terminal access
- 7. Appendix
- 7.1Hard disk capacity un
- 7.2Video required capaci
- Introduction
- 1.Product features overview
- 2.Operation explanation
- 3.Installation and connection
- 4.System function introduction
- 4.1Starting up / login / logout / restart / close
- 4.2Boot wizard
- 4.3 Video management
- 4.3.1 Search for device
- 4.3.2 Add device
- 1. Code matching instructions：
- 2:Code matching methods：
- 4.3.3 Advanced setups
- 4.3.4.Delete device
- 4.3.5 Repeater setup
- 4.3.6.Edit Channel
- 4.3.7.Encoding setup
- 4.3.8 Stream value
- 4.3.9 Channel details
- 2、Click Refresh, you can search the camera in curr
- 4.3.10 Channel OSD
- 3, Select the display setup, enter the location of
- 4.3.11 Camera
- 4.4 Network setup
- Click Reset to restore the information of the wire
- 4.5 PTZ setup
- 4.6 Recording
- 4.7 Video playback
- 4.8 Video backup
- 4.9 Alarm
- 4.10 General Setups
- 4.11 Equipment maintenance and management
- 5WEB Access
- 6.Mobile access
- 7.Appendix
Wireless NVR Kit Manual
23
3, Select the display setup, enter the location of communication icon adjustment. Can select position and
magnification.
4.3.11 Camera
Functional explanation：You can set the panorama camera installation mode
Steps：
1, Right Click the main interface, in the shortcut menu, select the system setup, select the channel setup -> camera.
As shown below:
2, Select the corresponding channel, the installation mode can choose wall, hanging, desktop
Explanation
The installation mode can be selected only when the panorama camera is connected
Currently can support the Panoramic cameras which support the N1 protocol
4.4 Network setup
4.4.1.Network setup
Explanation ： If the device is used for network monitoring, the network must be set up for normal use. Factory
default IP address: 192.168.1.114.
Steps：
1, Right click the main interface, in the shortcut menu, select the system setup, and then select the network setup. The
basic setup for the network setup are shown below:
Setup interface as shown below: