User Manual
Table Of Contents
- Intr
- 1.Product features overv
- 1.1Product introduction
- 1.2 Product parameters.
- 1.3Functional features
- 2.Operating instructions
- 2.1The front panel expla
- 2.2Rear Panel Interface
- 2.3The mouse operation i
- 2.4Input method instruct
- 2.5The remote control ope
- 2.6Interface specificatio
- 2.6.1Interface elements s
- 2.6.2Commonly used butto
- 2.7Menu description
- 3.Installation and conne
- 3.1Installation Notes
- 3.2Prepare before instal
- 3.3The camera placed in the
- 4.System function introdu
- 4.1Starting up/Login/Log
- 4.1.1 Starting up
- 4.1.2 Login
- 4.1.3 Logout
- 4.1.4 Restart
- 4.1.5 Close the screen o
- 4.1.6 Turn off
- 4.2Boot wizard
- 4.3 Video management
- 4.3.1 Search device
- 4.3.2 Add device
- 4.3.3 Advanced setup
- 4.3.4.Delete device
- 4.3.5Repeater function
- 4.3.6Edit channel
- 4.3.7Encoding setup
- 4.3.8Code stream value
- 4.3.9 Channels in detail
- 4.3.10 Channel OSD
- 4.3.11 Camera
- 4.4 Network Setup
- 4.4.1.Network Setup
- 4.4.2.Dynamic DNS
- 4.4.3.FTP26
- 4.4.4.E-Mail
- 4.4.5.PPPoE
- 4.4.6.3G
- 4.4.7.Wireless setup
- 4.5 PTZ setup
- 4.5.1 PTZ parameter setu
- 4.5.2 PTZ control operat
- 4.5.3 PTZ automatic crui
- 4.6 Video
- 4.6.1 Manual video
- 4.6.2 Timing video
- 4.6.3 The motion detecti
- 4.6.4 Alarm video
- 4.7 Video playback
- 4.7.1 Quick playback
- 4.7.2 Regular playback
- 4.8Video backup
- 4.9 Alarm
- 4.9.1Motion detecting al
- 4.9.2Video loss alarm
- 4.10 General setup
- 4.10.1General setup
- 4.10.2Timeset
- 4.10.3Screen setup
- 4.10.4Hard disk setup
- 4.11Device maintenance a
- 4.11.1 System information
- 4.11.2 User management
- 4.11.3 Restore the factor
- 4.11.4 System maintenanc
- 4.11.5 Software upgrade
- 4.11.6 IPC maintenance
- 5WEB access
- 5.1 Introduction
- 5.2 LAN Access
- 5.2.1 Login
- 5.2.2 Preview
- 5.2.3 Playback
- 5.2.4 Configuration
- 5.3 E-seenet access
- 5.3.1 E-seenet ID login
- 5.3.2 The user name logi
- 6.Mobile terminal access
- 7. Appendix
- 7.1Hard disk capacity un
- 7.2Video required capaci
- Introduction
- 1.Product features overview
- 2.Operation explanation
- 3.Installation and connection
- 4.System function introduction
- 4.1Starting up / login / logout / restart / close
- 4.2Boot wizard
- 4.3 Video management
- 4.3.1 Search for device
- 4.3.2 Add device
- 1. Code matching instructions：
- 2:Code matching methods：
- 4.3.3 Advanced setups
- 4.3.4.Delete device
- 4.3.5 Repeater setup
- 4.3.6.Edit Channel
- 4.3.7.Encoding setup
- 4.3.8 Stream value
- 4.3.9 Channel details
- 2、Click Refresh, you can search the camera in curr
- 4.3.10 Channel OSD
- 3, Select the display setup, enter the location of
- 4.3.11 Camera
- 4.4 Network setup
- Click Reset to restore the information of the wire
- 4.5 PTZ setup
- 4.6 Recording
- 4.7 Video playback
- 4.8 Video backup
- 4.9 Alarm
- 4.10 General Setups
- 4.11 Equipment maintenance and management
- 5WEB Access
- 6.Mobile access
- 7.Appendix
Wireless NVR Kit Manual
9
the IPC (wireless camera) and NVR should avoid the obstacle as much as possible. When the 4-channel video are
connected at the same time and there is no obstacle between the NVR and the IPC, the IPC is placed in a spherical
coverage area with a radius of 60 m with NVR as a center of gravity. The radius is reduced to 30 meters when there
are one wall between the NVR and the ipc. When there are two walls, it reduced to 15 meters radius (coverage
affected by the physical properties of the obstacles and the surrounding environment, this data is for reference only)
1, Connection steps
1、Connecting the NVR with the mouse and the display firstly, turn on the power of the NVR and the IPC, then
connect the NVR to the IPC with the cable. Right click on the mouse -> click on adding camera-> delete all channels
(Note: if only delete some bad channels, can click to delete the channel to delete the specified channel) -> code
matching -> "start code matching?" Click Yes -> Show "on the code matching" -> NVR monitor screen shows that
the success of the code matching(note: More than one camera can make code matching at the same time). If notify
the code matching fails, click "Refresh". If there is no indication that any network cable is bad, please re-connect to
the code matching operation. -> disconnect the network cable to see if the screen is normal, the screen normal means
that the wireless camera add successfully -> when all the wireless camera added to the NVR means that the
preparatory work is completed. (Figure 5.1, Figure 5.2, Figure 5.3, Figure 5.4)
2、Make sure the wireless NVR kit is working properly
NVR connection monitor, all the IPC installed around the NVR (Note: need to connect the antenna), power all
the device to complete the second step, when all the IPC video show on the NVR monitor, that means the kit is
working properly, can be installed to a predetermined location.
1, Unplug your NVR from power,unscrew and remove the top cover.
2, Connect the SATA power and data cables from the NVR to the corresponding ports on your HDD (as shown).
3, Holding the hard drive and the NVR ,gently turn it over and line up the holes on the hard drive with the holes on