User Manual

ManualsBrandsANOLiS ManualsCeiling LightANOLiS Ambiane AP Ceiling Light

User manual

Ambiane AP (RGBW, RGBA, TD, PW, TW)

The unit generates light by means of high power LEDs. The unit was designed for indoor use only.

1. Attention

 Theunitmustbeinstalledbyaqualiedelectricianinaccordancewithall

 nationalandlocalelectricalandconstructioncodesandregulations.

The unit was designed for indoor use only.

AvoidlookingdirectlyintotheLEDlightbeamatcloserange!

 Donotinstalltheunitnearhighlyinammableliquidsormaterials.

Do not allow anything to rest on the unit.

 Donotinstalltheunitnearanopename.

 Donotinstalltheunitindirty,dustyorbadlyventilatedlocation.

 Su󰀩cientairaccessingtothehousingoftheunithastobeensured,

there must not be any heat or anti-noise insulation within a 0.6m x 0.6m

 areaaroundtheunit(non-ICratedxture).

ImmunityoftheequipmentisdesignedforelectromagneticenvironmentsE1,E2,E3

 accordingtothestandardEN55103-2ed.2Electromagneticcompatibility.Productfamily

 standardforaudio,video,audiovisualandentertainmentlightingcontrolapparatusfor

 professionaluse.Part2:Immunity.

 Theproduct(coversandcables)mustnotbeexposedtoahighfrequencyelectromagneticeldhigher

 than3V/m.

 Theinstallationcompanyshouldchecklevelsofpossibleinterferencesabovethetestedlevels

 E1,E2,E3givenbythisstandard(e.g.transmittersinsurroundingarea)beforeinstallingtheequipment.

 EmissionoftheequipmentcomplieswiththestandardEN55032Electromagneticcompatibility

 ofmultimediaequipment–EmissionRequirementsaccordingtoclassB.

Suitableforfasteningon   Unsuitableforcoveringbyheatinsulation

 non-ammablesurfacesonly  material

Always switch o󰀨 power supply of the unit before connecting or disconnecting the unit

Summary of content (10 pages)

PAGE 1
User manual Ambiane AP (RGBW, RGBA, TD, PW, TW) The unit generates light by means of high power LEDs. The unit was designed for indoor use only. 1. Attention The unit must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations. The unit was designed for indoor use only. Avoid looking directly into the LED light beam at close range! Do not install the unit near highly inflammable liquids or materials.
PAGE 2
. Installation 1. Prepare a circular opening in the lower ceiling (1) as shown in the picture below. 2. Insert the Ambiane AP unit into the opening. Fasten the Ambiane AP by means of two spring fasteners (2) to the opening. 3. Connect needed cables to the Ambiane AP. Connection blocks (4) are placed on the PCB RB 3727 (3). The PCB is under plastic cover (5) which is fastened by means of two screws (6). The primary power input serves for a standard power (e.g. Power Supply for Ambiane AP).
PAGE 3
DMX connection PCB Function 0V Shield D+ Signal (+) DSignal (-) 0-10V connection PCB Function 0V 0V D+ +10V Power connection PCB Function + Power + Power - Recommended diameters of conductors with respect to distance between Ambiane AP and power supply unit (Ambiane Power AP). Distance/cable length 50 m Diameters of conductors 0.5 mm 100 m 2 1 mm2 3.
PAGE 4
AP will not respond to DMX commands) and deactivating command (0=OFF) to stop control of the Ambiane AP. DIP 11 has to be set in OFF position. Note: If DIP 11=OFF (Ambiane AP is controlled by DMX or DALI), the first coming command switches the Ambiane AP to the corresponding operation mode (DMX operation by a DMX command, DALI operation by a DALI command). E.g. the Ambiane AP stays in a DALI operation and coming DMX command switches the Ambiane AP to DMX operation.
PAGE 5
. Anti-glare ring installation Insert the anti-glare ring (1) into the Ambiane AP until three locks (2) snap into slots (3). 6. Adapter ring installation 1.Remove both spring fasteners (2) by unscrewing the four screws M4x10 (1). 2. Slide the adapter ring (4) onto the housing of the Ambiane AP. Screw the new fasteners (3) on the housing. Use original screws M4x10 (1).
PAGE 6
7. DMX protocols Ambiane RGBW , Ambiane RGBA Version 1.2 Mode 1 Channel Mode 2 Channe Mode 3 Channe Mode 4 Channe Mode 5 Channe 1 1 1 - 1 0-255 Red Red LEDs saturation control 0% -->100% proportional - - 2 - - 0-255 Red Fine Red LEDs saturation control from min. -->max. proportional 2 2 3 - 2 0-255 Green Green LEDs saturation control 0% -->100% proportional - - 4 - - 0-255 Green Fine Green LEDs saturation control from min. -->max.
PAGE 7
8. Technical specifications Input voltage: Protection class : Max. power consumption: Beam angle: Colour temperature: Ambiane PW Ambiane TW Ambiane TD Control: Ambiane RGBW, Ambiane TW Ambiane PW, Ambiane TD DMX channels: Ambiane RGBW Ambiane PW, Ambiane TD Ambiane TW Typical Lumen maintenance: Led life expectancy: Operating ambient temp.
PAGE 8
11. Dimensions mm [inch] 12. Maintenance Keep the Ambiane AP clean, especially light source and the ribbed housing.
PAGE 9
13. Software update Software update of the fixture can be done by means of the ROBE Uploader. It is a software for automatized software update of Robe and Anolis fixtures. It takes advantage of RDM support. The fixtures have to be connected in a daisy-chain (max. 32 fixtures) and via the Robe Universal Interface/ Robe Universal Interface WTX and a USB cable connected to the control PC with the Robe Uploader running. The control PC should be connected to the Internet.
PAGE 10
The Robe Uploader software and user manual is available at : https://www.robe.cz/robe-uploader/ Version 1.8 November 22, 2021 Specifications are subject to change without notice. Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o.