Phau Ntawv Qhia

ManualsBrandsANOLIS ManualsOutdoor LightAnolis 4 MC ArcSource Outdoor Light

User instructions

ArcSource Outdoor 4 MC

The ArcSource Outdoor 4 MC is a Cree MC-E RGBW multichip based high powered multicolored LED xture.

The unit can be used for large scale applications, as well as used for individual illuminating needs.

1.Attention

Consider the respective national norms during the installation!

Do not install the unit near naked ames.

Avoid using the unit in locations subject to possible impacts.

Do not attempt to dismantle or modify the unit.

Do not install the module in badly ventilated location

Avoid looking directly into the LED light beam at close range.

Immunity of the equipment is designed for electromagnetic environments E1, E2, E3

according to the standard EN55103-2 ed.2 Electromagnetic compatibility. Product family

standard for audio, video, audiovisual and entertainment lighting control apparatus for

professional use. Part 2: Immunity.

The installation company should check levels of possible interferences above the tested levels

E1,E2,E3 given by this standard (e.g. transmitters in surrounding area) before installing the equipment.

Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility

of multimedia equipment – Emission Requirements according to class B.

2.Installation

The ArcSource Outdoor 4 MC can be arranged in any position orientation. Three holes of diameter of 4.3mm

in the ArcSource Outdoor´s base serve for mounting on the non-ammable surface. The light head can be

adjusted against the base in range of 120°.

CAUTION!

Avoid looking directly into the LED light beam at close range!

CE: The ArcSource Outdoor units should be connected to the ArcPower drivers stated in technical specicati-

ons. See their user manuals for full details of mains power requirements and DMX operation.

Maximum possible number of LED modules connected to the one LED output of the ArcPower driver is men-

tioned in the table below.

Max.number of connected modules ArcPower drivers

12 ArcPower Rack Mount, DRS, ArcPower 48 Outdoor, ArcPower 192 Outdoor

6 ArcPower 24 outdoor

Use a cable splitter if more than one LED module has to be connected to the one LED output of the ArcPower

driver, the connection cable between the ArcPower and the splitter is a standard RJ45 patch cable category

5 wired 1:1.

US: The ArcSource Outdoor unit has to be connected to the power source of type of LVLE acording to the

specications stated in the chapter "Technical specications".

The enclosed adapter stand (with M5x45 screw) allows to place the light head to the higher position:

Summary of content (9 pages)

PAGE 1
User instructions ArcSource Outdoor 4 MC The ArcSource Outdoor 4 MC is a Cree MC-E RGBW multichip based high powered multicolored LED fixture. The unit can be used for large scale applications, as well as used for individual illuminating needs. 1.Attention Consider the respective national norms during the installation! Do not install the unit near naked flames. Avoid using the unit in locations subject to possible impacts. Do not attempt to dismantle or modify the unit.
PAGE 2
3.
PAGE 3
4.Technical specifications LED Device: Available beam angles: Colour variants: Max. Current per Colour: Max. Power Consumption: Recommened Power Supplies (CE): Recommened Power Supplies (US): Typical Lumen Maintenance: Led Life Expectancy: Cooling System: Operating Ambient Temp.
PAGE 4
7.
PAGE 5
Land spike 2 ASO 4 MC 100mm Land spike 1 ASO 4 MC 500mm Land spike 2 ASO 4 MC 500mm 5
PAGE 6
Land spike 3 ASO 4 MC 500mm Land spike 1 ASO 4 MC 100mm 6
PAGE 7
8. Installing the ArcSource Outdoor 4 MC onto a land spike Land spike 1 ASO 4 MC 100mm / Land spike 2 ASO 4 MC 100mm 1. Hammer the sharp part (1) of the land spike into ground (hammer the centre of the sharp part, not the edge). 2. Screw the threaded bar (2) into the sharp part (1) and secure it with the socket head M5x5 (3). 3 .Put the cover (4) on the threaded bar (2). 4. Put the pipe 36.5 mm (5) on the threaded bar (2). 5. Put the cable holder (6) on the threaded bar (2).
PAGE 8
Land spike Land spike 3 ASO 4 MC 500mm 1. Hammer the sharp part (1) of the land spike into ground (hammer the centre of the sharp part, not the edge). 2. Screw the threaded bar (2) into the sharp part (1) and secure it with the socket head M5x5 (3). 3 .Put the cover (4) on the threaded bar (2). 4. Put the pipe 36.5mm (5) on the threaded bar (2). 5. Put the cable holders (6) on the threaded bar (2). 6. Put the pipe 198mm (7) on the threaded bar (2). 7. Put the ArcSources holder (8) on the threaded bar (2).
PAGE 9
. Installing the top hat (half top hat) 1. Unscrew the Allen head screw (1) from the ArcSource Outdoor 4 MC housing. 2. Insert the distance part (4) into the housing of he ArcSource Outdoor 4 MC and place the top hat (half top hat) (5) on the housing (6). 3. Screw the Allen head screw (1) back to the housing with a spring washer (2) and flat washer (3). The small hook (7) ,which securing the top hat (half to hat) to the housing, has to be placed between the distance part (4) and the flat washer (3) .