AN-CPAL70-01 Cell Phone Signal Booster User Manual 1 / 11
Introduction With the popularity of mobile communications, people want to make a call anytime, anywhere, so the coverage requirement of communication network is higher and higher, but the reality is not so, sometimes mobile phone signal is not very good, you want to make a smooth call, even in some places cell phone cannot dial out. in this cases, cell phone signal booster can solve this problem in a certain extent.
Name Model Gain/Loss photo compliance. Do not remove the covers during working. Do not try to repair or replace any components inside of the equipment. Alteration or abuse of the equipment or other components will void this product’s warranty, and could be dangerous to the user. PACKAGE CONTENTS (1) Packages include the following： ① 1Pcs AN-CPAL70-01 Booster with N Female connectors. ②AC/DC Power Adaptor. ③Screws Mounting Kits. ④User manual (this document).
Indoor Antenna Rubber Antenna PTE-RB-800-2100 3dbi @698-787MHz 3dbi @824-894MHz 3.5dbi@1710-1755MHz 3.5dbi @1850-1990MHz 3.5dbi @1710-2155MHz Ceiling Antenna PTE-CI-800-2500 3dbi @698-787MHz 3dbi @824-894MHz 4.5dbi@1710-1755MHz 4.5dbi @1850-1990MHz 4.
Warning：Unauthorized antennas，cables and/or coupling devices are prohibited by FCC rules. Please contact FCC for details：1-888-CALL-FCC The antenna, cables, and other accessories of the booster kits shall not be modified without the approval of the ANNTLENT company, otherwise it shall be deemed invalid. INSTALLATION INSTRUCTIONS （1）Installation of Outdoor Antenna The booster’s main function is to improve weak RF signals of an area. A simple formula: Input power+ Gain= Output power.
best place that displays full bar signals to install the outdoor antenna. Selecting the installation direction of outdoor antenna. The outdoor antenna shall point to the direction of the tower, and it would be much better to keep line of sight. Please select the opposite directions for outdoor antenna and indoor antenna. If outdoor and indoor antennas have to be installed in the same direction, please install them only after the signal quality is tested and the self-oscillation is avoided.
If isolation can’t be achieved by the limited distance, the roof of the building or any other barriers can be used in between to increase isolation. Fix the donor antenna after selecting the best position, and adjust slightly its height or angles in order to get the signals with suitable input power level and calling quality. （2）Installation of Indoor Antenna Proper antennas shall be selected according to the site conditions and the requirement.
（3）Booster Installation Do not place the equipment in direct sunlight or in an area that has abrupt temperature and humidity changes . it is suggested that the booster is installed in a cool，dry and ventilated room without erosive gas and smoke. Connect power adaptor to the booster，connect The other end of power adaptor to the power outlet. WARNING: The input voltage for the booster is 5~12V DC. DO NOT use this Booster with a regular power supply that NOT 5~12V DC .
make a call During using your Booster, if the Booster interferes with your radio or other electronic device, move the Booster further away from those devices, you might be able to solve it yourself. If necessary，please contact your local dealer or send e-mail to our support team by the following methods: E-mail: support@ANNTLENT-tech.com If you want to know about ANNTLENT Company and products for more information, please visit at: www.ANNTLENT.
authorization for use of a particular booster model on behalf of all subscribers of individual providers. Alternatively, a provider may specify a testing protocol that if satisfied would result in licensee consent to specific booster models. A subscriber may also seek a licensee’s express consent to operate a signal booster, e.g.
on your invoice or sales receipt is the date of installation unless ANNTLENT or your reseller informs you. This warranty does not cover the following: Failure resulting from misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by you; The warranty is voided by removal or alteration of identification labels on the Machine or its parts.
