Tus neeg siv phau ntawv
Table Of Contents
- KNOW YOUR ESPRESSO COFFEE MAKER
- FROTHING MILK
- 1. Turn the Steam Controller all the way to “OFF” position to close the steam nozzle.
- 2. Use the handle to turn the milk frother out to the side of the machine.
- 3. Press the Steam button “”, and the Steam indicator light will start flashing.
- 4. Wait until the Steam indicator light stop flashing.
- 5. Fill approx. 100ml of cold milk in milk jug. Ideally, a milk jug is made of stainless steel.
- 6. Pick up the milk jug and guide the nozzle of milk frother and immerse it lightly into the milk.
- 7. Hold the milk jug at a slight angle and turn the Steam controller to the “/” position.
- 8. Move the milk jug up and down slightly, but ensure the nozzle is always immersed in the milk.
- 9. Once you have created sufficient milk froth, close the Steam controller and place the milk jug aside. Wipe the nozzle with a clean damp cloth.
- 10. Press the Power button to turn OFF the machine.
- After milk frothing, the steam nozzle must be cleaned. Not doing so may result in steam blockage.
- Press the power button “” to turn off the machine.
- Pull the power plug off from the mains power outlet socket.
- Allow the machine cool down for a few minutes.
- Quick clean
- Wipe all parts with a damp soft cloth, such that coffee grounds and milk residues do not dry on the machine.
- Empty the drip tray
- The drip tray needs emptying as soon as the red overfill indicator pops up.
- Carefully lift the drip tray off the espresso machine, remove the draining rack and pour the water into the sink.
- Dispensing amount for a single-cup
- Dispensing amount of double-cup
- Restore factory setting
- After pressing the power ON button, if there is no function selected within 29 minutes, the unit will power off automatically.
- After pressing the power button, if there is no function selected after the water pump has operated for more than 180 seconds during frothing, the pump will stop automatically.
Emptying the brewing filter
1. Remove the filter holder from the machine.
2. Turn the filter holder to “
Lock
” mark position, then pull it
down gently.
3. Fold the filter blocker up and over the edge to hold the
brewing filter. Refer to figure shown.
4. Hold the handle placing your thumb/finger on the filter
blocker, this will prevent the filter from falling out, turn it
upside down and knock out remove the espresso
powder.
FROTHING MILK
1. Turn the
Steam Controller
all the way to “
OFF
” position to close the steam nozzle.
2.
Use the handle to turn the milk frother out to the side of the machine.
3. Press the
Steam button
“ ”, and the
Steam indicator
light will start flashing.
4. Wait until the
Steam indicator
light stop flashing.
Note: Prior to frothing milk, it is recommended to clean the steam nozzle. To do this, hold an empty
large cup underneath the milk frother nozzle and turn on the steam controller. Wait for approx. 15
seconds, then close the steam controller. Place the large cup aside and start frothing milk.
5. Fill approx. 100ml of cold milk in milk jug. Ideally, a milk jug is made of stainless steel.
6. Pick up the milk jug and guide the nozzle of milk frother and immerse it lightly into the milk.
7. Hold the milk jug at a slight angle and turn the
Steam controller
to the “ / ” position.
8. Move the milk jug up and down slightly, but ensure the nozzle is always immersed in the milk.
9. Once you have created sufficient milk froth, close the
Steam controller
and place the milk jug
aside. Wipe the nozzle with a clean damp cloth.
10.
Press the
Power button
to turn OFF the machine.
Note: After making steam, you can press “Single-cup” or “Double-cup” button immediately to brew
coffee again. The “Single-cup” and “Double-cup” indicator will flash quickly if the temperature is too
high. At this time, you need to reduce the temperature by following the operation as below. Turn the
knob to “Hot water” setting “ / ”, and then the hot water will dispense. When the temperature
goes down, the pump will stop automatically and you should turn the knob off, then you can brew
coffee again.
If you do not want to brew coffee when the high-temperature warning occurs, you can press the
“Single-cup” or “Double-cup” button again to cancel.