Tus neeg siv phau ntawv
Table Of Contents
- KNOW YOUR ESPRESSO COFFEE MAKER
- FROTHING MILK
- 1. Turn the Steam Controller all the way to “OFF” position to close the steam nozzle.
- 2. Use the handle to turn the milk frother out to the side of the machine.
- 3. Press the Steam button “”, and the Steam indicator light will start flashing.
- 4. Wait until the Steam indicator light stop flashing.
- 5. Fill approx. 100ml of cold milk in milk jug. Ideally, a milk jug is made of stainless steel.
- 6. Pick up the milk jug and guide the nozzle of milk frother and immerse it lightly into the milk.
- 7. Hold the milk jug at a slight angle and turn the Steam controller to the “/” position.
- 8. Move the milk jug up and down slightly, but ensure the nozzle is always immersed in the milk.
- 9. Once you have created sufficient milk froth, close the Steam controller and place the milk jug aside. Wipe the nozzle with a clean damp cloth.
- 10. Press the Power button to turn OFF the machine.
- After milk frothing, the steam nozzle must be cleaned. Not doing so may result in steam blockage.
- Press the power button “” to turn off the machine.
- Pull the power plug off from the mains power outlet socket.
- Allow the machine cool down for a few minutes.
- Quick clean
- Wipe all parts with a damp soft cloth, such that coffee grounds and milk residues do not dry on the machine.
- Empty the drip tray
- The drip tray needs emptying as soon as the red overfill indicator pops up.
- Carefully lift the drip tray off the espresso machine, remove the draining rack and pour the water into the sink.
- Dispensing amount for a single-cup
- Dispensing amount of double-cup
- Restore factory setting
- After pressing the power ON button, if there is no function selected within 29 minutes, the unit will power off automatically.
- After pressing the power button, if there is no function selected after the water pump has operated for more than 180 seconds during frothing, the pump will stop automatically.
the “Single-cup indicator” flashes at the same time, when the desired amount is dispensed, press
the “Single-cup” button again, the coffee will stop dispensing. At that time, the setting for the
dispensing amount of single cup is finished and it will be saved for next operation. The adjustable
dispensing amount of single cup ranges between 15 seconds and 25 seconds.
Dispensing amount of double-cup
Hold and press the “Double-cup” button for 3 seconds to enter into the mode of setting the
dispensing amount, then follow the operation of setting the dispensing amount of single cup. The
adjustable dispensing amount of double-cup ranges between 25 seconds and 45 seconds.
Restore factory setting
Simultaneously hold and press the “Steam” and “Double-cup” buttons for 3 seconds to recover the
factory setting of dispensing amount.
AUTOMATICALLY POWER-OFF FUNCTION
After pressing the power ON button, if there is no function selected within 29 minutes, the unit will
power off automatically.
After pressing the power button, if there is no function selected after the water pump has operated
for more than 180 seconds during frothing, the pump will stop automatically.
CLEANING AND MAINTENANCE
DANGER OF BURNING!
The espresso machine becomes hot during operation. Metal parts particularly
remain hot for longer time.
Prior to cleaning, wait until the espresso machine has cooled down completely.
SHORT-CIRCUIT HAZARD!
Water, which has penetrated the housing, may cause a short-circuit. Never immerse
the espresso machine in water or other liquids. Ensure that no water or other liquids
enter into the housing.
Always switch off the machine and pull off the plug mains power before
cleaning!
RISK OF DAMAGE!
Improper handling of the espresso machine may result in damage. Do not use any
aggressive detergents, sharp or metallic cleaning implements, such as knives, hard
spatulas and similar. These may damage the surfaces.
1. Clean the filter holder, brewing filter and the drip tray with a little detergent under warm running
water and rinse through with clear water.
2. Pull the metal nozzle off the milk frother and clean it with a little detergent under warm running
water. Rinse it thoroughly with clear water.
3. Wipe the handle and the milk frother with a slightly damp cloth.
4. Let all parts dry before reassembling.
5. Regularly wipe down the housing of the machine with a slightly damp cloth.