Sparta Series 865BLED INSTRUCTIONS
Thank you for choosing Angler. The 865BLED from Angler’s Sparta Series is a slim, lightweight, and powerful LED fixture that will add versatility to your set. This fixture is ideal for head shots, portraits, and interviews on small sets due to its color accuracy and precise brightness and color temperature control. It operates on plug-in power, but when you need to take it to a location shoot, it also operates on two NP-F batteries.
Do not attempt to disassemble or repair the equipment. There are high-voltage components inside the unit. Failure to observe this precaution could result in electric shock or product malfunction. This will void the warranty, and Angler will not be responsible for any damage. Use only the correct, recommended voltage. Make sure the unit is powered off when plugging it into a power source. Disconnect the power cord when not in use. Do not stare directly at the lights when they are powered on.
Overview Barndoors Accessory slots Locking tab LED array Two-way 5/8 inch receiver Yoke Diffuser Locking knob 4
LED display Power input Tab release buttons Tilt locks Battery plates Channel select button Power button Adjustment knob Also included: Check battery button AC power cord AC power adapter and cord Travel Case 5
Mounting the 865BLED 1. Make sure the tilt locks are securely tightened before mounting the fixture. 2. Loosen the locking knob, and mount the receiver vertically or horizontally onto a light stand with a 5/8 in. baby pin. 3. Tighten the locking knob until secure. 4. Once the light is securely mounted, loosen the tilt locks to adjust to position of the light. Powering On the Light AC Power When operating on AC power, remove the batteries. 6 1.
Battery Power When operating on battery power, unplug the power adapter from the AC outlet and from the light. 1. Place two NP-F batteries into the battery plates, and slide them toward the contacts until the battery is firmly in place. 2. Press and hold the power button until the light comes on. Press the battery check button to see the remaining charge in your batteries. 1 Pro tip: For uninterrupted operation, pack a few extra batteries in your gear bag. Adjusting the Color Temperature 1.
Adjusting the Brightness 1. Press the adjustment dial so the LED appears under Dimmer. 2. Select the output level from 10 to 99. Wireless Operation The brightness and color temperature settings can be controlled remotely from up to 100 feet away with the Genaray MB-WRT Wireless Remote (sold separately). 1. To set a channel on the 865BLED, press the channel button, and select the channel with the adjustment knob. 2. Press the channel button again to confirm the selection.
Diffuser and Barndoors Removing the Barndoors and Diffuser 1. Move either one of the tab release buttons and lower the locking tab. 2. Slide the barndoors and/or the diffuser off the accessory rails. 1 To replace the Barndoors and Diffuser 1. Raise one of the locking tabs to its locked position. Make sure the other locking tab is lowered to the unlocked position. 2. Slide the diffuser into the inner accessory slot, and slide the barndoors into the outer accessory slot. 3.
Specifications LIGHT FIXTURE LED Chip Type SMD LED Output Power 36 W Beam Angle 60° Color Temperature 3200 to 5600 K Color Accuracy Standard CRI 94.6 TLCI 96.5 Cooling System None Dimming Yes, 10% - 100% in 1% increments Display LED Housing Material Metal Photometrics 3200 K: 2609 lx @ 3 ft. 4400 K: 2854 lx @ 3 ft. 5600 K: 2766 lx @ 3 ft. Number of LEDs 160 Expected Lamp Life 50,000 HR. Dimensions (W×H×D) Light: 8 × 6.9 × 1.5 in. (20.3 × 17.5 × 3.8 cm) With Yoke: 12 × 10.75 × 2 in.
MOUNTING Fixture Mount Two-way 5/8 in. receiver YOKE Yoke Material Metal Yoke Type Yoke/Bracket Tilt 360° Remote Operation Remote Control Type 2.4 GHz Number of Channels 99 Wireless Range 100 ft. (30 m) POWER AC Input Power 100 to 240 V AC, 50/60 Hz DC Input Power 13 to 19 V DC Power Adapter 15 V, 2.
One-Year Limited Warranty This Angler product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
