WDP Angel Manual WDP Angel Owner's Manual This is an exact replication of the WDP AngelTM Owner's Manual. I recieved permission from WDP before duplicating this manual. Although all the text is property of WDP, the html coding is property of Sun Enterprise's and is copyrighted. Linking of this page is only permitted with written permission from myself to ensure sponsors and content of other pages are not obscene or illegal.
WDP Angel Manual ● Fault finding tables 36-38 ● Warranties 39-40 ● UK & Foreign Patents applied for Important Safety Guidelines Rules for safe Marker handling Treat every marker as if it were loaded ● Insert barrel bung when not in use ● Always remove gas source when not in use NOTE: The AngelTM can hold a small gas charge, typically 2 shots. With the gas source removed, fire to remove this surplus gas. ● Ensure isolator switch is "off" when not in use. ● Only use 0.
WDP Angel Manual The LED on the charger will indicate the status of the charging cycle on the AngelTM. 1. NO LED power at cigar socket not present! Switch ignition on 2. DIM RED LED isolator switch on AngelTM is on Switch isolator off 3. BRIGHT RED LED FLASHING indicates battery conditioning from totally discharged battery 4. GREEN LED indicates trickle charging occuring, battery achieved 30% capacity NOTE: The AngelTM may be left charging for prolonged periods without damage occuring to the battery pack.
WDP Angel Manual the buttons which may be done to bleed your gas supply system prior to disconnection. Warning: The AngelTM will hold sufficient gas for 2 shots after isolation. Switching the AngelTM On (SEE FIG.2) The electrical isolator/safety switch may now be swicthed "on" toward the rear of the marker. A green LED will illuminate on the rear of marker. WARNING - Adhere stricly to all safety warnings the AngelTM is now in an armed state.
WDP Angel Manual Pull the "pull knob" and rotate 90 degrees so that the knob remains in the unlocked position Stage 3 Swing the brech block so that the bolt is exposed Stage 4 Retract the bolt Stage 5 Replace the bolt follow stages in reverse order NOTES: Caution, do not fire the AngelTM with the breech open or without the bolt in the breech. Caution, do not fire the AngelTM with the pull knob in the unlocked position.
WDP Angel Manual Stage 2 - Decrease rate of fire Rotate the top oot on the circuit board anticlockwise to reduce the reate of fire. Minimum setting achievable is 6 shots per second. Stage 3 - Increase rate of fire Rotate the top ot on the circuit board clockwise to increase the rate of fire, maximum achievable is 15 shots per second.
WDP Angel Manual Insert/remove shims as necessary each shim equals approximately 2.5 psi (0.17 BAR). Stage 5 Replace springs in correct order onto the piston Stage 6 Re-insert the pistion ensuring that it is located correctly and replace end-cap Stage 7 Gas up the AngelTM and check pressure EXHAUST VALVE REMOVAL (SEE FIG.
WDP Angel Manual Item 10 - Ensure the hole for item 5 is in the correct orientation prior to refitting Item 8 - Ensure the springs are in the right order Item 5 - Ensure the pin locates into the hole in itme 10 Item 5 - Ensure O ring is present when item 3 is replaced. RAM STROKE ADJUSTMENT PATENTS APPLIED FOR (SEE FIG.
WDP Angel Manual Follow ram stroke adjustment procedure for disassembly and access. Stage 2 Item 7 - Remove snap ring nut using suitable metric allen key. Ensure that item 6 does not move by holding in place with circlip pliers. Item 8 - Remove with suitable pick, replace if worn or damaged. Stage 3 Replace item 5, locking the breech/bolt in place. Stage 4 Replace item 7 ensuring the ram/hammer assembly item 6 does not rotate (secure using circlip pliers) until slight resistance is felt.
WDP Angel Manual Note: Item 3 is a hard seal Item 4 is a soft seal Stage 4 Replace items 4-1 Stage 5 Re-gas system, check for leaks. Picture of Dissasembled AngelTM Part No.
WDP Angel Manual AL060 Hammer AL061 Ram Body Seals AL070 Ram Snap Ring 90 Shore AL071 Ram Snap Ring Screw AL073 Breech Blok Pivot Screws 4BA AL074 Breech Blok Seal 70 Shore AL075 Breech Blok Pivot Pin (FRONT) AL076 Breech Blok Pivot Pin (REAR) AL077 Breech Blok Lock Pin AL078 Breech Blok Lock Pin Spring AL079 Breech Blok Release Knob AL082 Bolt AL084 Exhaust Valve AL086 Exhaust Main Body AL087 Exhaust Body Lock Pin 1 3 1 1 2 1 1 1 1 1 1 1 1 1 1 AL148 Anti Double Ball Anodized AL149 LPR Body Anodized AL15
WDP Angel Manual Stage 1 Ensure the AngelTM is switched 'on' and gassed up. Stage 2 Remove the 2 fixing screws item 1 using suitable metric allen key. Stage 3 Gently lift off the cover plate item 2 and ensure the wires do not become snagged. Stage 4 Using a sharp pencil press and hold the orange button item 4. The pneumatics will now operate as all the electronics are bypassed. Stage 5 On removing the pencil the pneumatics will reset. This shows that pneumatics have functioned correctly.
WDP Angel Manual VIEWLOADERTM VL2001 INTILIFEEDTM PANTENTS APPLIED FOR The AngelTM has the abaility to power and control the VL2001 which will greatly enhance the performance of the AngelTM with a 40% increase in feed rate over existing standard hoppers.
WDP Angel Manual VELOCITY TOO LOW/HIGH? IS INLET FROM HIGH PRESSURE REGULATOR SET CORRECTLY? IS VELOCITY ADJUSTER SCREW SET CORECTLY? IS BOLT STICKING? SEE PROPELLANT GAS SUPPLY SEE VELOCITY ADJUSTMENT CHECK MOVEMENT IS LPR SET CORRECTLY? SEE LPR ADJUSTMENT IS VALVE DWELL SET CORRECTLY? SEE ELECTRONIC VALVE DWELL ADJUSTMENT IS RAM SET CORRECTLY? SEE RAM STROKE ADJUSTMENT IS SNAP RING SET CORRECTLY? SEE RAM SNAP RING ADJUSTMENT CHOPPING BALLS IS SUITABLE WORKING HOPPER FITTED? IS RATE OF FIRE SET
WDP Angel Manual negligence, abnormal working conditions, weather, accident, tampering, failure to follow the manufactures instructions (whether oral or in writing), misuse or alteration or repair of the AngelTM without the company's written approval will invalidate this warranty and the company shall be under no obligation whatsoever to the purchaser in respect of any of the above breaches of this warranty.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig1.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig1.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig2.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig2.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig3.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig3.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig4.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig4.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig5.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig5.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig67.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig67.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig8.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig8.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig9.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig9.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig10.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig10.
http://www.geocities.com/Pipeline/Curb/8754/gfx/fig11.jpg http://www.geocities.com/Pipeline/Curb/8754/gfx/fig11.
