Data Sheet

Magnetic Encoder Kit
For CIM Motor
Phoenix America, INC
4717 Clubview Drive
Fort Wayne, IN 46804
Tel: [phone]
Local: (260)-432-9664
Fax: [phone]
www.phoenixamerica.com
[e-mail]
© Copyright Phoenix America 2015, rev. 1/27/16
Physical Outline
5.11mm
.20in (X4)
ON A 2.0 INCH B.C.
60.96mm
2.40in
9.53mm
.38in
0mm
0in
7.94mm
.31in
9.53mm
.38in
NOTE: 2 DEG. TAPER
ON THIS EDGE
5
4
3
2
1
6810M999
SHEET 1 OF 1
01
SCALE: 1:1
FORMAT
SW
REV DWG. NO.
A
SIZE
TITLE:
PHOENIX AMERICA INC.
4717 CLUBVIEW DRIVE; FT. WAYNE, INDIANA 46804
D. POOLE
BLANK MAGNET
CHECKED DRAWN
ECO# DATE REV.
PHOENIX AMERICA INC.
CLAIMS PROPRIETARY RIGHTS
IN THE MATERIAL DISCLOSED
HERON. THIS DOCUMENT IS
ISSUED IN CONFIDENCE AND
MAY NOT BE USED TO
REPRODUCE OR
MANUFACTURE ANYTHING
SHOWN WITHOUT WRITTEN
PERMISSION FROM PHOENIX
AMERICA INC.
DATE
08/6/2015
NOTE
DIMENSIONS ARE IN INCHES
TOLERANCES UNLESS
OTHERWISE NOTED:
.XX
0.01 ANGLES 0.15
.XXX 0.005
.XXXX
0.0015
Electrical Parameters
Pin # Function Type Parameter Notes:
1 VDD Supply +4 to 24 VDC ABS Max -0.3 / +32.0 VDC
2 Ch A Open Drain 15mA Max I-sink
Duty Cycle 40% to 60%, A/B phase shift 80° to 90°,
Maximum frequency 5KHz.
3 GND Supply Gnd 0 V
4 Ch B Open Drain 15mA Max I-sink
Operating Temperature -40°C to +95°C
Storage Temperature -55°C to +150°C
11.43mm
.45in
7.98mm
.314in
25.65mm
1.01in
0mm
0in
5.08mm
.20in
6.73mm
.27in
#4-40 x 3/32"
SET SCREW
MAGNET
MATERIAL
HUB
MATERIAL
Notes:
Magnet Material is WPM575 1.
Hub Material Aluminum 6061 2.
Magnetized 60 poles (30 N, 30 S) radially with 3.
equal spacing.
RELEASED 12/11/15 15-070 01
5
4
3
2
1
3111M060
SHEET 1 OF 1
01
SCALE: 1:1
FORMAT
SW
REV DWG. NO.
A
SIZE
TITLE:
PHOENIX AMERICA INC.
4717 CLUBVIEW DRIVE; FT. WAYNE, INDIANA 46804
D. POOLE
PANCAKE ENCODER
MAGNET ASSEMBLY
CHECKED DRAWN
ECO# DATE REV.
PHOENIX AMERICA INC.
CLAIMS PROPRIETARY RIGHTS
IN THE MATERIAL DISCLOSED
HERON. THIS DOCUMENT IS
ISSUED IN CONFIDENCE AND
MAY NOT BE USED TO
REPRODUCE OR
MANUFACTURE ANYTHING
SHOWN WITHOUT WRITTEN
PERMISSION FROM PHOENIX
AMERICA INC.
DATE
12/09/2015
NOTE
DIMENSIONS ARE IN INCHES
TOLERANCES UNLESS
OTHERWISE NOTED:
.XX
0.01 ANGLES 0.15
.XXX 0.005
.XXXX
0.0015
Target MagnetEncoder
R
pull up
VDD
Encoder IC
Gnd
CH A
Vss
10KΩ
Signal
Out A
0.1 μF
R
pull up
CH B
Vss
10KΩ
Signal
Out B
Decoupling Capacitor
Included inside Encoder
Pull up resistors are necessary to generate an output signal for the
desired voltage level and are generally preferred external for
encoders.
Red Black
Yellow Blue
Pin 1
Ch A
Ch B
Channel A leads channel B when the CIM
motor is running in positive polarity (red
wire + and black wire -)
Vdd
Signal Phasing