Installation Instruction

ManualsBrandsAndrew Wireless System ManualsElectronicsION-U Extension Unit for cellular systems

The Remote Unit, Extension Unit or Master Unit has to be

mounted by proffessionel / special trained installer.

1.1. HIGH POWER EU MECHANICAL INSTALLATION

1.1.1. Health and Safety for mechanical installation

Read and observe the notices in chapter 1.3 Health and Safety.

1. Caution: Risk of injury by the considerable weight of the unit falling. Ensure there is

adequate manpower to handle the weight of the system.

2. Caution: Risk of serious personal injury by equipment falling due to improper installation.

The installer must verify that the supporting surface will safely support the combined load

of the electronic equipment and all attached hardware and components. The screws and

dowels (wall anchors) used should also be appropriate for the structure of the supporting

wall.

1.1.2. Property Damage Warnings for mechanical installation

1. Attention: Do not install the unit in a way or at a place where the specifications outlined in

the Environmental and Safety Specifications leaflet of the supplier are not met.

2. Attention: Due to power dissipation, the unit may reach a very high temperature. Ensure

sufficient airflow for ventilation.

3. Notice: Exceeding the specified load limits may cause the loss of warranty.

4. Notice: When connecting and mounting the cables (RF, optical, mains, ...) ensure that no

water can penetrate into the unit through these cables.

5. Notice: If any different or additional mounting material is used, ensure that the mounting

remains as safe as the mounting designed by the manufacturer. The specifications for

stationary use of the Unit must not be exceeded. Ensure that the static and dynamic

strengths are adequate for the environmental conditions of the site. The mounting itself

must not vibrate, swing or move in any way that might cause damage to the Unit.

Specified torques must be observed for certain mounting procedures according to the following table:

Type Pins Hex nuts Screws

Thread

M 6 M 6 M6

Specified torques

3.3 N-m 3.3 N-m 3.3 N-m

Summary of content (7 pages)

PAGE 1
Installation Instruction The Remote Unit, Extension Unit or Master Unit has to be mounted by proffessionel / special trained installer. 1.1. HIGH POWER EU MECHANICAL INSTALLATION 1.1.1. Health and Safety for mechanical installation Read and observe the notices in chapter 1.3 Health and Safety. 1. Caution: Risk of injury by the considerable weight of the unit falling. Ensure there is adequate manpower to handle the weight of the system. 2.
PAGE 2
1.2. ELECTRICAL INSTALLATION 1.2.1. Health and Safety for electrical installation Read and observe the notices in chapter 1.3 Health and Safety. 1. Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Electrical hazard.
PAGE 3
9. Notice: Use an appropriate torque wrench for the coupling torques: - for N-type connectors (2 N-m / 20 in lb) with 13/16 in opening, e. g. item no. 244379 available from the CommScope e-catalog - for 4.3-10 type connectors (5 N-m, 44 in lb) with 22mm (7/8) in opening Do NOT use your hands or any other tool (e.g. a pair of pliers). This might cause damage to the connector and lead to a malfunction of the unit. 10.
PAGE 4
1.3. 1. HEALTH AND SAFETY Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Electrical hazard. Danger of death or fatal injury from electrical current inside the unit in operation. Before opening the unit, disconnect mains power. 3.
PAGE 5
1.5. COMPLIANCE 1. Notice: For installations which have to comply with European EN50385 exposure compliance requirements, the following Power Density limits/guidelines (mW/cm²) according to ICNIRP are valid: o o o 0.2 for frequencies from 10 MHz to 400 MHz F (MHz) / 2000 for frequencies from 400 MHz to 2 GHz 1 for frequencies from 2 GHz to 300 GHz 2.
PAGE 6
4. Notice: Corresponding local particularities and regulations must be observed. For national deviations, please refer to the respective documents included in the manual CD that is delivered with the unit. 5. Notice: The unit complies with Overvoltage Category II.
PAGE 7
Equipment Symbols Used / Compliance Please observe the meanings of the following symbols used in our equipment and the compliance warnings: Symbol Compliance --- FCC CE Meaning / Warning For industrial (Part 20) signal booster: WARNING: This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device.