User's Manual

Figures and Tables
MF0200A5C_ION-U_L_7_80-85_17EP_19P.docx Manual for ION
®
-U Page 5
FIGURES AND TABLES
figure 3-2 Remote Unit, SISO ..................................................................................... 18

figure 3-3 Remote Unit, MIMO two units paired ......................................................... 18 
figure 3-4 One RU one EU one antenna .................................................................... 18 
figure 3-5 Two RUs one EU two antennas ................................................................. 19 
figure 3-6 RU connectors and Status LED ................................................................. 19 
figure 4-1 Mounting bracket ........................................................................................ 22 
figure 4-2 Pole-mounting kit 4" to 18" ......................................................................... 24 
figure 4-3 Pole-mounting kit 40” ................................................................................. 24 
figure 4-4 RU threaded pin power supply side ........................................................... 25 
figure 4-5 RU threaded pin narrow side ..................................................................... 25 
figure 4-6 Place RU onto wall mounting bracket – single mount ............................... 26 
figure 4-7 Install M6x12 screws and washers for single mount ................................. 27 
figure 4-8 Attach M6 nut to threaded pins for single mount ....................................... 27 
figure 4-9 Completed SISO RU mount ....................................................................... 28 
figure 4-10 1
st
RU placed on wall mounting bracket - MIMO ..................................... 29 
figure 4-11 Install M6x12 screws and washers .......................................................... 29 
figure 4-12 Attach M6 nut to threaded pins ................................................................ 30 
figure 4-13 2
nd
RU on wall mounting bracket ............................................................. 30 
figure 4-14 Install M6x12 screws and washers 2
nd
RU .............................................. 31 
figure 4-15 Attach M6 nut to threaded pins for 2
nd
RU ............................................... 31 
figure 4-16 Completed MIMO RU mount .................................................................... 32 
figure 4-17 Grounding bolts ........................................................................................ 36 
figure 4-18 Grounding bolt, schematic view ............................................................... 36 
figure 4-19 AC power cable ........................................................................................ 37 
figure 4-20 DC power cable ........................................................................................ 37 
figure 4-21 Vdc/100 power cable ................................................................................ 38 
figure 4-22 Connect mains plug ................................................................................. 39 
figure 4-23 Antenna connection ................................................................................. 45 
figure 4-24 Expansion ports ........................................................................................ 46 
figure 4-25 Alarm connector ....................................................................................... 46 
figure 4-26 Pwr/Ctrl connector .................................................................................... 47 
figure 4-27 RS-232 connector .................................................................................... 47 
figure 4-28 Remove optics cover ................................................................................ 50 
figure 4-29 Remove sealing nut ................................................................................. 51 
figure 4-30 Split-seal and clamp jacket ...................................................................... 51 
figure 4-31 Optical cables connected ......................................................................... 52 
figure 4-32 Place cables into split-seal ....................................................................... 52 
figure 4-33 Optical cable installed .............................................................................. 53 
figure 4-34 Alarm triggering ........................................................................................ 56 
figure 5-1 Disconnect mains power ............................................................................ 60 
figure 5-2 RU power supply location .......................................................................... 61 
figure 5-3 8 RU power supply screws ......................................................................... 61 
figure 5-4 RU power supply with cables ..................................................................... 61 
figure 5-5 RU power supply input cable ..................................................................... 62 
figure 5-6 RU power supply output cable ................................................................... 62 
figure 5-7 RU with power supply removed ................................................................. 62 
figure 5-8 RU insert power supply .............................................................................. 63 