PSR 700/800 MHz Public Safety Repeaters Manual MF0123A1A
DISCLAIMER: This document has been developed by CommScope and is intended for the use of its customers and customer support personnel. The information in this document is subject to change without notice. While every effort has been made to eliminate errors, CommScope disclaims liability for any difficulties arising from the interpretation of the information contained herein.
Table of Contents TABLE OF CONTENTS 1. GENERAL 6 1.1. USED ABBREVIATIONS 6 1.2. HEALTH AND SAFETY 7 1.3. PROPERTY DAMAGE WARNINGS 7 1.4. COMPLIANCE 8 1.5. ABOUT COMMSCOPE 12 1.6. 1.6.1. 1.6.2. 1.6.3. CONTACTING COMMSCOPE CommScope Mobility Solutions (CMS) Technical Support Accessing DCCS User Documentation CMS Technical Training 13 13 13 13 2. INTRODUCTION 14 2.1. PURPOSE 14 2.2. PSR 700/800 MHZ 0.5/2W 14 3. FUNCTIONAL DESCRIPTION 15 4. COMMISSIONING 16 4.1. 4.1.1. 4.1.2. 4.
Table of Contents 6.3. EULA ACCEPTANCE PAGE 31 6.4. LOGIN PAGE 32 6.5. MAIN PAGE 32 6.6. 6.6.1. 6.6.2. 6.6.3. 6.6.4. 6.6.5. 6.6.6. 6.6.7. 6.6.8. 6.6.9. 6.6.10. 6.6.11. 6.6.12. SYSTEM SETTINGS License Upgrade Software Upgrade Restore Factory Defaults My Account Management IP Settings OMC Connection Alarm Settings General RF Settings 700 MHz Channels (Class A Only) 800 MHz Channels (Class A Only) Site Location Time and Date 33 33 34 35 36 37 38 39 40 41 42 43 43 6.7. 6.7.1. 6.7.2. 6.7.3. 6.7.4. 6.
Figures and Tables FIGURES AND TABLES figure 3-1 Configuration of a PSR 700/800 MHz 0.5/2W, analogue variant .............. 15 figure 3-2 Configuration of a PSR 700/800 MHz 0.5/2W, digital variant ................... 15 figure 4-1 Connectors of PSR 700/800 MHz............................................................. 19 figure 4-2 Grounding bolts (left) and schematic view (right) ..................................... 19 figure 4-3 Alarms cable ............................................................
1. General 1. General 1.1.
1. General 1.2. Health and Safety 1. Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Electrical hazard. Danger of death or fatal injury from electrical current inside the unit in operation. Before opening the unit, disconnect mains power. 3.
1. General 9. Do not disassemble the unit. 10. Notice: Make sure the repeater settings are correct for the intended use (refer to the manufacturer product information) and regulatory requirements are met. Do not carry out any modifications or fit any spare parts, which are not sold or recommended by the manufacturer. 1.4. Compliance 1.
1. General 4. Notice: For installations which have to comply with FCC/ISED requirements: English: This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This device complies with Health Canada’s Safety Code 6.
1. General 5. Notice: The unit complies with Overvoltage Category II. It also complies with the surge requirement according to EN 61000-4-5 (fine protection); however, installation of an additional medium (via local supply connection) and/or coarse protection (external surge protection) is recommended depending on the individual application in order to avoid damage caused by overcurrent.
1. General Equipment Symbols Used / Compliance Please observe the meanings of the following symbols used in our equipment and the compliance warnings: Symbol Compliance --- FCC --- ISED Meaning / Warning For industrial (Part 90) signal booster: This is a 90.219 Class B device. WARNING: This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device.
1. General 1.5. About CommScope CommScope is the foremost supplier of one-stop, end-to-end radio frequency (RF) solutions. Part of the CommScope portfolio are complete solutions for wireless infrastructure from top-of-the-tower base station antennas to cable systems and cabinets, RF site solutions, signal distribution, and network optimization. For patents see www.cs-pat.com. CommScope has global engineering and manufacturing facilities.
1. General 1.6. Contacting CommScope 1.6.1. CommScope Mobility Solutions (CMS) Technical Support For additional information, please contact CMS Technical Support: Telephone Helplines: Call one of the Telephone Helpline numbers listed below to get live support, 24 hours a day. Global 24X7 +1 888-297-6433 (Toll free for U.S.
2. Introduction 2. Introduction 2.1. Purpose This manual contains information and procedures for the operation of the Commscope Public Safety Repeaters PSR 700/800 MHz 0.5/2W Class A and Class B. The purpose of this document is to provide a step-by-step procedure to help experienced technicians or engineers install and commission an in-building wireless enhancement system using Commscope repeater.
3. Functional Description 3. Functional Description figure 3-1 Configuration of a PSR 700/800 MHz 0.5/2W, analogue variant figure 3-2 Configuration of a PSR 700/800 MHz 0.
4. Commissioning 4. Commissioning Read and observe the health, safety, and property damage warnings as well as the description carefully to avoid mistakes and proceed step-by-step as described. • Attention: Do not operate the PSR without terminating the antenna connectors. The antenna connectors may be terminated by connecting them to their respective antennas or to a dummy load.
4. Commissioning 5. Notice: Do not place cables or tools that may damage the repeater in close proximity to it. 6. Notice: Do not wear jewelry or metal accessories when installing this repeater. 7. Notice: When connecting and mounting the cables (RF, optical, mains, ...) ensure that no water can penetrate into the unit through these cables. 8. Notice: Check all cables for shorts and opens. Verify that there are no cables with loose or poor connections.
4. Commissioning 4.2. Electrical Installation 4.2.1. Health and Safety for Electrical Installation Read and observe chapter 1.2 Health and Safety. 1. Danger: Electrical hazard. Danger of death or fatal injury from electrical current. Obey all general and regional installation and safety regulations relating to work on high voltage installations, as well as regulations covering correct use of tools and personal protective equipment. 2. Danger: Electrical hazard.
4. Commissioning 4.2.3. Connections Power connector, e.g. for UPS (not part of delivery) DO NOT USE LAN/Ethernet connector Measurement probe for donor antenna Connector for alarm cable Connector for donor antenna Measurement probe for coverage antenna Connector for coverage antenna figure 4-1 Connectors of PSR 700/800 MHz 4.2.4. Grounding (Earthing) Grounding must be carried out. Connect an earth-bonding cable to the M6 grounding connections provided at the outside of the repeater.
4. Commissioning 4.2.5. Connection of the Antenna Cables The PSR has 4.3-10-type antenna connector. Please refer to section 4.2.3 for its location. Refer to the corresponding documentation of the connector manufacturer for mounting the cable connectors. The bending radius of the antenna cables must remain within the given specifications. Choose the type of cable best suited for the antenna. Consider that a cable with higher loss is less expensive but impairs performance.
4. Commissioning 2. Remove protective cap from the RF connector. Caution: Risk of injury by flying particles when compressed air is used. Wear protective clothing, especially protective glasses. 3. Remove metal chips and small particles from the mating and inner surfaces of the connector using compressed air. Warning: Flammable material. Risk of fire. Keep away from sources of ignition. Caution: Eye irritant product. Risk of eye irritation. Avoid contact with eyes and skin.
4. Commissioning 6. Clean the inside surface of the inner ring with a cotton bud drenched with isopropyl alcohol. 7. Clean the inside of the center conductor spring tines with a cotton bud drenched with isopropyl alcohol. 8. Clean in the similar way the connector of the connected cable. Remove protective caps from the unit connector first. 9. Remove metal chips and small particles from the mating and inner surfaces of the connector using compressed air. 10.
4. Commissioning 11. Continue with the inside mating surface of the inner ring. 12. Clean the outside surface of the center pin. 4.2.7. Antenna Cable Connector Assembly The figures in this chapter illustrate the connection procedure and do not show the actual unit. 1. What is needed for the connector assembly? a. Torque wrench. b. (Adjustable) counter wrench 2. Join the connectors and turn the coupling nut until the thread grips.
4. Commissioning 3. Push in the connector until it clicks. 4. Fasten the coupling nut hand-tight. Do not turn the connector but the coupling nut only. 5. Retain the cable connector with the counter wrench and fasten the coupling nut with the torque wrench until the torque is applied (torque wrench clicks). Torque wrench For angled antenna connectors use your hand to retain the cable connector and fasten the coupling nut with the torque wrench.
4. Commissioning 4.2.8. Alarms Connection For the location of the ALARM RELAY connector, refer to chapter 4.2.3.
4.
4. Commissioning 4.2.10. Power Connection Before connecting electrical power to the RU, the system must be grounded as described in section 4.2.4 Grounding (Earthing). Connect the power supply plug of the power supply cable that is part of the delivery at the POWER connector of the unit (see section 4.2.3).
5. Status LEDs, Alarms, and Troubleshooting 5. Status LEDs, Alarms, and Troubleshooting For local supervision, three multi-color LEDs (Power, OSC, and Alarm) are part of the front panel to display unit status information. During booting and SW update, all three LEDs blink green, indicating that initialization and isolation measurement are in process. When the boot process is finished, and the repeater works properly, all three LEDs are green to indicate normal operation.
5. Status LEDs, Alarms, and Troubleshooting Troubleshooting in case of unknown IP address or password: If the IP address or password was inadvertently changed or forgotten so that access to the Web GUI is not possible, a Reset button inside the unit is provided. Note: Be aware that this button will set back all data to factory defaults.
6. Description of Web GUI 6. Description of Web GUI 6.1. LAN Settings at Local PC In order to have access to the Web GUI, the following network adapter settings need to be set at the local PC. Setting a static IP address in the same address range (see below 192.168.1.5) is required: Access the LAN settings of your local PC and click Properties: Select Internet Protocol Version 4 (TCP/IPv4) and click Properties: → Enter the IP address and click OK.
6. Description of Web GUI 6.2. Required Software The Web GUI uses Ethernet TCP/IP communication and Protocol uses RFM Protocol. SNMPv2 MIB Protocol. Default Ethernet telecommunication specification. • URL Address: http://192.168.1.150 • Default Username: admin • Default Password: admin • Browser: Chrome Internet Browser 6.3. EULA Acceptance Page When a user connects first time or after a factory reset, the EULA Acceptance page appears. If you do not Accept the EULA, login to the repeater is not possible.
6. Description of Web GUI 6.4. Login Page Enter Username and password exactly. If you enter Username and password incorrectly, the message is shown below. If you typed username and password wrongly more than 3 times, input of username and password input will be locked for 30 seconds. 6.5. Main Page • • System Reboot Button : The entire system is rebooted (about 10 seconds are required.) Logout Button : System logging out.
6. Description of Web GUI • • • • Display Version: Indicated with Version 01.00.00.XX Alarm Status : : If more than one critical alarm is generated, mark it as Critical. If No alarm status, mark is as Clear. Main Menu : It is configured with the System Settings / System Operation menu. Temperature : It display system temperature. 6.6. System Settings 6.6.1. License Upgrade • Device Information indicates as below.
6. Description of Web GUI 6.6.2. Software Upgrade Click the Choose file button and select Software update file, open it Press the Update button to update the Software. Once Software Uploading is complete (this will take around 1 minute), proceed as follows When Software Updating is complete, you automatically move to the Login page. NOTE: Do not turn off the device during software updates.
6. Description of Web GUI 6.6.3. Restore Factory Defaults Note: Be aware that only RF Settings will be saved in the backup file and that after the restore all ALC buttons will be set to ON and all Amplifier buttons will be set to OFF irrespective of the settings made before. Save Backup Button: When you click the button, the system's RF Setting information is downloaded to your PC as backup.dat file. Restore File Choose File Button: Click the Button and select the Backup file to open.
6. Description of Web GUI 6.6.4. My Account Management My Information: You can update Username, Company, Contact Number, Email Address, and Role information. Change Password Button: You can change Password. Password must be at least eight characters and must contain Latin / alphanumeric characters. Also, you must include at least one Capital letter/small letter/number.
6. Description of Web GUI 6.6.5. IP Settings Factory Default IP Setting • IP Address : 192.168.1.150 • Subnet Mask : 255.255.255.0 • Broadcast : 192.168.1.255 • Gateway : 192.168.1.1 • Primary DNS : 168.126.63.1 • Secondary DNS : 168.126.63.2 If you press Save button after changing IP Address, the following message appears: Click OK button to IP Settings and then System will be reboot.
6. Description of Web GUI 6.6.6. OMC Connection OMC Server IP Address: A Total of 5 OMC Server IP Addresses can be inputed. Factory Default IP Address : 0.0.0.0 Alarm Notification: Heartbeat ON / OFF Function Heartbeat Interval Time Set Function : 1 ~ 1440min can be set.
6. Description of Web GUI 6.6.7. Alarm Settings In the Alarm Setting dialog box, you can mask/unMask the alarm. Click the Active button in the Alarm list to set up the ON/OFF Toggle. And then, press the Save button to save the Alarm settings. • • Active ON : When an alarm is triggered, the alarm LED and alarm relay are selected and MIB Notification Alarm is generated. Active OFF : When an alarm is triggered, Alarm LED and Alarm Relay are not selected, MIB Notification Alarm is also Masked.
6. Description of Web GUI 6.6.8. General RF Settings Screen for Class A (Digital) 700/800MHz Band Feature] update of screen shot required Only the items corresponding to Feature Key ID are Active and RF Setting is available. RF Setting: ALC : ON /OFF HPA : ON/OFF User ATTN : User Gain Control (0~ 30dB) / Step 0.
6. Description of Web GUI 6.6.9. 700 MHz Channels (Class A Only) 700 MHz Band Digital Filter Channels Configuration • Broad Band(LTE) : CH1, CH2 Filter BW : OFF, 5 MHz,10MHz,18MHz • Narrow Band : CH3 ~ CH34 Filter BW : OFF, 12.5, 25, 50, 75, 100, 150, 200 kHz Center Freq. Setting : Set up the Center Freq. per each Channel. Center Freq. Range : 758.000000 ~ 775.000000 (MHz) Ref : DL Freq. Digital Gain Setting : DL/UL Gain Control per each Channel Digital Gain Control Range : +/- 5 dB Step 0.
6. Description of Web GUI 6.6.10. 800 MHz Channels (Class A Only) 800 MHz Band Digital Filter Channels Configuration • Broad Band(LTE) : CH1, CH2 Filter BW : OFF, 5 MHz,10MHz,18MHz • Narrow Band : CH3 ~ CH34 Filter BW : OFF, 12.5, 25, 50, 75, 100, 150, 200 kHz • Center Freq. Setting : Set up the Center Freq. per each Channel. Center Freq. Range : 851.000000 ~ 869.000000 (MHz) Ref : DL Freq. Digital Gain Setting : DL/UL Gain Control per each Channel Digital Gain Control Range : +/- 5 dB Step : 0.
6. Description of Web GUI 6.6.11. Site Location Enter the Site Location information and press the Save button to save the Site Location information on the Device. CompanyName: You can enter up to 30 characters Address: You can enter up to 30 characters City: You can enter up to 30 characters State/Province/Territory : You can enter up to 10 characters Zip Code: You can enter up to 10 characters Contact: You can enter up to 20 characters 6.6.12.
6. Description of Web GUI Save Button: Save the changed Date/Time and Time Zone on the Device. PC Time Set: Save the Date/time of the PC to the device (However, Time Zone should set to item 1). Note: Date/Time is reset if the repeater power is left off for more than 2 days 6.7. System Operation 6.7.1. Active Alarm update of screen shot required 1) You can view the current Active Alarm. 2) Alarm test is a function that performs an Alarm Simulation.
6. Description of Web GUI 6.7.2. Alarm History • Alarm History Function If an Alarm occurs in the Repeater, it must be stored in the Alarm History. If the User switches On the Alarm Test to test the Alarm, the Manual Trigger Alarm Log must be saved. • Alarm History Log File Alarm Event file is named as occurred date. And the file saved on System Alarm History Folder. Ex) 20190226.log • Alarm History Log File Content Saved as a Csv file, seperated by commas.
6. Description of Web GUI 6.7.3. Event History • Event History Function The function to store user Logging information and history of changing RF settings • Event History Log File Event file is named as occurred date. And the file saved on System Event History Folder. Ex) 20190226.log • Event History Log File Content Saved as a Csv file, seperated by commas.
6. Description of Web GUI 6.7.4. Antenna Isolation Check Click the Test button to start the Antenna Isolation Check. When the Isolation Check is completed, display the Isolation value and Maximum Gain.
6. Description of Web GUI 6.7.5. VSWR Check Press Test Button to display the current VSWR Ratio. If the Return loss value is less than the Threshold value, the VSWR Fail Alarm is generated. The shading will change from green to red in case of an alarm.
6. Description of Web GUI 6.7.6. 700MHz Band Overview [Figure: 700 MHz Band Class A RF Overview] update of screen shot required Displays the current 700 MHz band setting and the Input/Output Power Level. If you want to check the status again, you can click the 700 MHz Band menu button or F5 refresh key to perform the status check. Automatic gain reduction is indicated by orange color. 6.7.7.
7. Maintenance 7. Maintenance 7.1. General Read and observe chapter 1.2 Health and Safety. Caution: The unit reaches high temperature in operation. Risk of burns by hot surface. Do not touch the unit before it has sufficiently cooled down. Note: The repeater does not require preventative maintenance measures. Note: We recommend checking the cleanliness of the unit and in particular of the heat sink at appropriate intervals depending on the degree of dust and dirt at the installation site.
8. Appendix 8. Appendix 8.1.
8.
8. Appendix 8.2. Specifications 8.2.1. RF Performance 700MHz Band Frequency range UL Frequency range DL Instantaneous bandwidth RF technology Duplex UL/DL output power max. per band for 2 W type UL/DL output power max. per band for 0.
8. Appendix 8.2.2. Power Specifications Parameter Value Power consumption Dual Band Typ. 140 W, Max. 160 W Power consumption Single Band Typ. 100 W, Max. 120 W AC Power supply 88 ~ 264 VAC / 60 Hz (50 Hz / 60 Hz) DC Power supply -62 ~ -33 VDC All figures are typical values, unless otherwise stated. All data is subject to change without notice. 8.2.3. Mechanical Specifications Parameter Specification Remark Size(mm) 400 x 480 x 170 mm WxLxH Weight 19 Kg Antenna Port 4.3.
8. Appendix Salt mist EN 60 068 Storage (ETS 300 019 –2 –1, class 1.2) Temperature Vibration (sinusoidal) Vibration (random) Shock Humidity Water - 25° to + 70° C 5 – 62 Hz / 0.5 mm displacement 0.2 g @ 62 – 200 Hz, 3 x 5 sweeps 0.02 m2/s3 10 – 50 Hz +12 dB / Oct. 5 – 10 Hz -12 dB / Oct. 50 – 100 Hz 3 x 30 min none + 30° C / 93 % / 96 h none All data is subject to change without notice.
8. Appendix 8.3. Available Configurations and SW Feature Keys Feature Keys: Feature Key ID 7835720 7835721 7835687 7835689 785359 Remarks Feature Description 2W, Dual Band 2W, Single Band 0.5W, Dual Band 0.5W, Single Band Lock Device 800 MHz only 800 MHz onl The Feature Key ID does not distinguish between Class A, B and DC, AC type. A detailed list of available configurations is provided in the following.
9. Index 9. Index A H About CommScope .............................................. 12 Alarm Relay .......................................................... 25 Alarms .................................................................. 28 Health and Safety ................................................... 7 B Illustrations ..................................................... 51, 52 Installation Electrical .......................................................... 18 Mechanical .....................