Installation Guide

M0201AKC CommScope Era
™
High Power Carrier Access Point Installation Guide — Preliminary
© April 2019 CommScope, Inc. Page 17
Safely Working with a CAP H
4 Notice: For installations which have to comply with FCC/ISED requirements:
English:
This device complies with FCC Part 15. Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This device complies with Health Canada's Safety Code. The installer of this device should ensure that RF
radiation is not emitted in excess of the Health Canada's requirement. Information can be obtained at
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
AntennaStmtforISED:
This device has been designated to operate with the antennas having a maximum gain of 9 dBi. Antennas
having a gain greater than 9 dBi are prohibited for use with this device without consent by ISED
regulators. The required antenna impedance is 50 ohms.
The antenna(s) used for this transmitter must be installed to provide a minimum separation distance (as
specified in
Table 6) from all persons and must not be co-located or operating in conjunction with any
other antenna or transmitter. Users and installers must be provided with antenna installation
instructions and transmitter operating conditions for satisfying RF exposure compliance.
French:
Cet appareil est conforme a FCC Partie15. Son utilisation est soumise a Les deux conditions suivantes: (1)
cet appareil ne peut pas provoquer d'interferences et (2) cet appareil doit accepter Toute interference, y
compris les interferences qui peuvent causer un mauvais fonctionnement du dispositif.
Cet appareil est conforme avec Sante Canada Code de securite 6. Le programme d'installation de cet
appareil doit s'assurer que les rayonnements RF n'est pas emis au-dela de I'exigence de Sante Canada. Les
informations peuvent etre obtenues:
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php
Les changements ou modifications non expressement approuves par la partie responsable de la
conformite pourraient annuler l'autorite de l'utilisateur a utiliser cet equipement.
AntenneStmtpourISDE:
Ce dispositif a ete designe pour fonctionner avec les antennes ayant un gain maximal de 9 dBi. Antennes
ayant un gain plus grand que 9 dBi sont interdites pour une utilisation avec cet appareil sans le
consentement des organismes de reglementation d'ISDE. L'impedance d'antenne requise est 50 ohms.
L'antenne (s) utilise pour cet emetteur doit etre installe pour fournir une distance de separation minimale
(comme indique dans le
Table 6) par rapport a toute personnes et ne doit pas etre co-localisees ou
operant en conjonction avec une autre antenne ou emetteur. Les utilisateurs et les installateurs doivent
etre fournis avec des instructions d'installation de l'antenne et des conditions de fonctionnement de
l'emetteur pour satisfaire la conformite aux expositions RF.
5 Notice: The unit complies with Overvoltage Category II. It also complies with the surge requirement
according to EN 61000-4-5 (fine protection); however, installation of an additional medium (via local
supply connection) and/or coarse protection (external surge protection) is recommended depending on
the individual application in order to avoid damage caused by overcurrent.
For Canada and US, components used to reduce the Overvoltage Category shall comply with the
requirements of IEC 61643-series. As an alternative, components used to reduce the Overvoltage
Category may comply with ANSI/IEEE C62.11, CSA Certification Notice No. 516, CSA C22.2 No. 1, or UL
1449. Suitability of the component for the application shall be determined for the intended installation.