Installation & Assembly

ManualsBrandsAndover Mills Manuals5 Piece Kitchen & Dining Room SetsTilley Rustic 5 Piece Dining Set

Model No:

KEEP FOR FUTURE REFERENCE.

Date of purchase:

_______ / _______ / _______

Lot number:

_____________________________________

(TAKEN FROM CARTON)

5-PC TRADITIONAL

HEIGHT DINING SET

CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND

INSTRUCTION MANUAL

NOTE:

THIS INSTRUCTION BOOKLET

DO NOT RETURN PRODUCT TO THE STORE.

If a part is missing or damaged, contact our customer service

department. We will replace the part FREE of charge.

ASSISTANCE

RN PRODUCT TO STORE

E-MAIL:DAS@DOREL.COM

Summary of content (9 pages)

PAGE 1
INSTRUCTION MANUAL 5-PC TRADITIONAL HEIGHT DINING SET Model No: NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Lot number: (TAKEN FROM CARTON) _____________________________________ Date of purchase: _______ / _______ / _______ DO NOT RETURN PRODUCT TO THE STORE. If a part is missing or damaged, contact our customer service department. We will replace the part FREE of charge.
PAGE 2
NOTES: * Ensure all parts and components are present before beginning assembly. * Assemble on a soft, smooth surface to prevent damage to product finish. * Phillips head screw driver is not included. * DO NOT use power tools. * CAUTION: Adult assembly required. * Assembly will require two people. * Estimated assembly time: 30 minutes. CARE AND CLEANING Dust table regularly with a soft, dry cloth to prevent soil build up. A dampened cloth may be used occasionally to clean the surface.
PAGE 3
5-PC TRADITIONAL HEIGHT DINING SET HARDWARE LIST 1 2 Ø5/16" X 23MM NUT 8 PCS 3 FLAT WASHER 8 PCS 4 Ø5/16" X 19MM Ø5/16" X 11MM FLAT WASHER 36 PCS SPRING WASHER 44 PCS 5 6 Ø5/16" X 1-1/2" Ø5/16" X 3" BOLT 4 PCS BOLT 16 PCS 7 8 LEFT END (A-L) 1 PC ENDPANEL PANEL RIGHT ENDPANEL PANEL (A-R) 1 PC MATTRESS END SUPPORT 1PC Ø5/16" X 2-1/4" BOLT 16 PCS 9 ALLEN KEY 1 PC ALLEN WRENCH 1 PC
PAGE 4
5-PC TRADITIONAL HEIGHT DINING SET PARTS LIST A B TABLE TOP TABLE LEG 1 PC 4 PCS C D BACK FRAME SEAT FRAME 4 PCS 4 PCS E CHAIR LEG 8 PCS
PAGE 5
-PC TRADITIONAL HEIGHT DINING SET STEP 1 With the help of another person, place table top (A) upside down on a clean, smooth surface. Attach table legs (B) to table top (A) with nuts (1), spring washers (4) and flat washers (2). Use Allen Wrench (8) to tighten nuts (1).
PAGE 6
5-PC TRADITIONAL HEIGHT DINING SET STEP 2 Attach seat frame (D) to back frame (C) with bolts (6), spring washers (4) and flat washers (3) through the corners of seat frame (D). Secure the center of seat frame (D) to back frame (C) with bolt (5), spring washer (4) and flat washer (3). Use Allen key (9) to install the bolts. NOTE: Do not fully tighten the bolts. Leaving them loose will facilitate assembly in the following step.
PAGE 7
5-PC TRADITIONAL HEIGHT DINING SET STEP 3 Attach the legs (E) to seat frame (D) with bolts (7), spring washers (4) and flat washers (3). Use Allen key (9) to tighten the bolts. NOTE: Tighten all the bolts installed in previous steps. Repeat steps 2 and 3 to assemble the remaining chairs.
PAGE 8
5-PC TRADITIONAL HEIGHT DINING SET CAUTION: This unit is intended for use only with the products and/or maximum weights indicated. Use with other products and/or products heavier than the maximum weights indicated may result in instability or cause possible injury. Product Maximum W eight 100 lbs That's it ! You've finished assembling your dining set. DO NOT RETURN PRODUCT TO THE STORE. If a part is missing or damaged, contact our customer service department. We will replace the part FREE of charge.
PAGE 9
Customer Service PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CONTACT CUSTOMER SERVICE REPRESENTATIVES AT THE FOLLOWING NUMBERS SHOULD THERE BE ANY MISSING OR DEFECTIVE PART(S).