Datasheet

www.andersonpower.com
- 61 -
All Data Subject To Change Without Notice
SECTION 3 SB
®
50
ID
Length
Wire Entrance
990 990G1 5905
Self attaching discrete conductor. Bolt on discrete conductor. Bolt on bundled conductors.
The given wire O.D. information is an estimate. Cable clamps should be evaluated for performance with the actual wire to be used.
Dust Cover
Prevents dust and dirt from entering the mating interface of
the connector when unmated. NOTE: Not a Hermetic Seal.
Description ---- Part Numbers ----
Minimum Quantity .............................. 500 50 ...
Dust Cover with Lanyard Strap, Red 113890P1 134G1
SB
®
Environmental Boots
SB
®
Environmental Boots provide water, dirt, chemical and UV protection for SB
®
50
connectors. The durable boots shield the connectors from water and dirt to IP64* in
both the mated and unmated condition.
Description ---------- Part Numbers --------
Minimum Quantity ...................................... 250 25 ...
SB
®
50 Environmental Boot with Cover, Load 3-6054P2-BK 3-6054P2
SB
®
50 Environmental Boot with Cover, Source 3-6055P2-BK 3-6055P2
SB
®
50 Environmental Boot (no cover), Load 3-6054P1-BK 3-6054P1
SB
®
50 Environmental Boot (no cover), Source 3-6055P1-BK 3-6055P1
*IP64 test pending
Guide Housings for Vertical Mini Powerclaw Contacts
Prevents polarity being reversed when a SB
®
50 is mated
to vertical mini Powerclaw contacts.
Description ------------ Part Numbers -----------
Minimum Quantity .... 1,000 50 ......
Black Guide Housing PC-HSG-SB-BK PC-HSG-SB
Cable Clamps
Durable metal cable clamps securely hold cables to prevent accidental strain or pulls from dislodging
wire or contacts from the housing. Cable clamps are recommended for solder terminated wires.
Cable Size
AWG or mm² or
Description (Inches O.D.) (mm O.D.) ---- Part Numbers ----
Minimum Quantity ........................................................................................... 500 50 ...
Self Attaching for Discrete Conductor 8 to 6 10 990-BK 990
Self Attaching for Discrete Conductor 12 to 10 4 to 6 990G2-BK 990G2
Bolt on for Discrete Conductor 12 to 6 4 to 10 990G1-BK 990G1
Bolt on for Bundled Conductor (0.320 to 0.450) (4.27 to 11.43) 5905-BK 5905
Reducing Bushings
Use with contact part number 5900-BK or 1307-BK to allow a smaller wire to be used with the connector.
Electrical capability is derated with smaller wire.
Dimensions
- ID - - Length -
Contact Barrel Size Wire Size -------- Part Numbers -------- inches mm inches mm
Minimum Quantity ...................................................... 3,000 1,000 100 ...................................................
#6 AWG [13.3 mm²] #8 AWG [8.4 mm²] - 5912-BK 5912 0.18 4.57 0.45 11.43
#6 AWG [13.3 mm²] #12- 10 AWG [3.3- 5.3 mm²] 5910-BK - 5910 0.14 3.56 0.47 11.94
#6 AWG [13.3 mm²] #16- 14 AWG [1.3- 2.1 mm²] 5913-BK - 5913 0.09 2.29 0.47 11.94
15702 DS-SB50 REV C4.0
NEW
Slide cover over
mating end.
PCB
SB50 Connector
Mini-vertical
Powerclaw
Contacts
Guide
Housing
A
B
C
Dimensions
- A - - B - - C -
in mm in mm in mm
5.9 151.4 1.8 45.1 6.3 160