Datasheet

www.andersonpower.com
- 26 -
All Data Subject To Change Without Notice
| PP15-45 & POWERPOLE
®
PAK SPECIFICATIONS |
SECTION 2 Powerpole
®
PP15 to 45
Electrical
Current Rating Amperes¹ UL 1977 CSA/TUV
Singlepole Wire to Wire (10 AWG) 55 40
Singlepole Ground Wire to Wire or PCB (10 AWG) 45 35
3x3 Block Wire to Wire (10 AWG) 40 27
Singlepole 25A PCB to Wire (12 AWG) 25 -
2x3 Block 25A PCB to Wire (12 AWG) 25 22 *
Singlepole 45A PCB to Wire (10 AWG) 45 40 *
2x3 Block 45A PCB to Wire (10 AWG) 45 25 *
Voltage Rating AC/DC
UL 1977 600
PCB Connector Recommended Voltage³
per IEC 60950-1 Table 2L Pollution Degree
2
25A Contacts Adjacent Poles 495
25A Contacts Separated by Spacer 1,000
45A Contacts Adjacent Poles 160
45A Contacts Separated by Spacer 970
Dielectric Withstanding Voltage
Volts AC 2,200
Avg. Mated Contact Resistance Milliohms¹
15A Wire Contact with 5/8” of #16 AWG 0.875
30A Wire Contact with 5/8” of #12 AWG 0.600
45A Wire Contact with 5/8” of #10 AWG 0.525
45A PCB Contact to Contact 0.500
25A PCB Contact to Contact 0.600
UL Hot Plug Current Rating Amperes
250 cycles at 72V DC 45A
250 cycles at 120V DC 30A
UL Ground Short Time Current Test - 45A Premate Ground
750 Amps, #10 AWG Wire 4 Seconds
470 Amps, #12 AWG Wire 4 Seconds
Mechanical
Wire Size Range AWG mm²
20 to 10 0.75 to 6.0
Max. Wire Insulation Diameter in. mm
0.175 4.450
Operating Temperature² °F °C
Powerpole
®
Housings & Powerpole
®
Pak Shells -4° to 221° -20° to 105°
Mating Cycles No Load by Plating Silver (Ag) Tin (Sn)
PCB to Wire - 1,500
Wire to Wire 10,000 1,500
Avg. Mating / Unmating Force Lbf. N
Low Force Wire, High Force PCB, & Ground 3 13
High Force Wire 5 22
Low Force PCB 2 9
Min. Contact / Spring Retention Force Lbf. N
20 90
Powerpole
®
Pak Latch Avg. Defeat Force Lbf. N
150 667
PCB Specications
Mounting Style Plated Through Hole
PCB Thickness- in. [mm] 0.090 - 0.150 (2.3-3.8)
25A PCB Recommended Traces #12 AWG Cross Section
45A PCB Recommended Traces #10 AWG Cross Section
Min. Creepage / Clearance Distance PCB in. mm
25A Creepage & Clearance Adjacent Poles 0.201 5.1
45A Creepage & Clearance Adjacent Poles 0.067 1.7
Mechanical Shock
4
MIL-STD-202 213 Condition A 50g’s
Vibration High Frequency
4
MIL-STD-202 204 Condition A 10g’s
Materials
Housing
Plastic Resin Polycarbonate
Contact Retention Spring Stainless Steel
Housing Flammability Rating
UL94 V-0
Contact
Base Copper Alloy
Plating Tin or Silver
Contact Termination Methods
Crimp³ Wire Contacts
Hand Solder 1331, 1332 & PCB Contacts
Solder Dip PCB Contacts
Wave Solder PCB Contacts
Protection
Touch Safety with Finger Proof Housings & Wire
Contacts or PCB Mating Interface
UL1977 Sec. 10.2 Pass
IEC 60950 Pass
IEC 60529 IP20
Touch Safety Standard Housings
IEC 60529 IP10
* No TUV Recognition
1
Based on: 105°C rated or better cable of the largest size, Properly calibrated APP
®
recommended tooling, and a 25°C ambient temperature. UL rating not to exceed the
maximum operating temperature. CSA rating below a 30°C temperature rise.
2
Limited by the thermal properties of the connector plastic housing.
3
Use APP
®
recommended tooling only. Alternate tools may adversely affect the
performance of our connectors along with UL and CSA recognition.
4
Tested with contact part number 261G2.