Datasheet

www.andersonpower.com
- 24 -
All Data Subject To Change Without Notice
SECTION 2 Powerpole
®
Pak
Plug Shell With Latch Shown
Shell, housing and contacts
are sold separately.
Retaining Pin
Conduit Clamp
With Screws
Retaining Pin
[ 27.94 ]
1.10
[ 1.78 ]
0.07
[ 19.56 ]
0.77
E
NOTE: Retaining pins are used to secure and
position Powerpoles
®
in one of two positions in
receptacle shells.
Retaining Pin
Cable Clamp
With Screws
Shell, housing and contacts
are sold separately.
Plug Shell Without Latch Shown
Shell and housing are
sold separately.
Clamp
Retaining
Pins
Screws
NEW
NEW
Plug Shell with Latch & Non-Conductive Strain Relief
New 2X3 Powerpole Pak offers an improved ergonomic shell for easier latch operation as
well as a plastic, non-conductive strain relief. The new strain relief can accommodate up
to a 6 conductor #10 AWG cable. Can mate to a panel mount receptacle. For use with
Powerpole
®
wire connectors only. Cable Clamp and Hardware Pak or Retaining Pins
must be ordered separately. To be used with 115G23 cable clamp only.
Description -------- Part Numbers -------
Minimum Quantity 1,000 25 ...
Black, 5-6 Poles 1460G23-BK 1460G23
Snap-in Receptacle Shell
Mate to plug shells with or without latches, or mate to another panel mount receptacle to create a bulkhead to
bulkhead connection. For use with Powerpole
®
wire or PCB connectors. Order the number of retaining pins for
each receptacle as shown below separately.
Number of Dimensions Knock Out Size
Retaining Pins - E - - Width -
Description ---------------- Part Numbers ---------------- to Order inches mm inches mm
Minimum Quantity ... 1,000 500 25 ...............................................................................
Black, 2-4 Poles 1470G1-BK - 1470G1 1 1.50 38.10 1.25 31.75
Black, 5-6 Poles - 1470G2-BK 1470G2 2 1.88 47.75 1.62 41.15
Black, 7-8 Poles - 1470G3-BK 1470G3 3 2.13 54.10 1.88 47.75
Black, 9-10 Poles - 1470G4-BK 1470G4 4 2.44 61.98 2.19 55.63
* Height = [25.4 mm] 1.0 in.
Cable Clamp & Hardware Pak
Includes cable clamp, 2 screws, and required amount of retaining pins for each conguration.
Screw Head Cable
Description Type Type ------------ Part Numbers ------------
Minimum Quantity .................................... 1,000 500 25 ...
2-4 Poles Straight Slot Bundled 115G1-BK - 115G1
5-6 Poles Straight Slot Bundled 115G2-BK - 115G2
7-8 Poles Straight Slot Bundled 115G3-BK - 115G3
9-10 Poles Straight Slot Bundled - 115G4-BK 115G4
2-4 Poles Philips Bundled 115G7-BK - 115G7
5-6 Poles Philips Bundled 115G8-BK - 115G8
Cable Clamp & Hardware Pak
Includes 2 cable clamp halfs, 2 screws and 2 retaining pins. To be used with
1460G23 Plug Shell only.
Screw Head Cable
Description Type Type ------ Part Numbers ------
Minimum Quantity ….…… 1,000 25
5-6 Poles Philips Bundled 115G23-BK 115G23
Flexible Conduit Clamp & Hardware Pak
Includes cable clamp, 2 screws, and need amount of retaining pins for each conguration.
Description - Part Number -
Minimum Quantity ...... 100 ......
2-4 Poles 110G10
Retaining Pin for Snap-in Receptacle
Order the number of retaining pins for each receptacle shown in the Snap-in Receptacle
Shell ordering information. Pins are also required for the plug side when the Cable Clamp &
Hardware Pak is not ordered.
Description ----- Part Number ------
Minimum Quantity ..... 1,000 100 ...
Retaining Pin 110G9-BK 110G9
NOTE: Max wire O.D. for
1460G23 is 0.80 inches
[20.3 mm²].
[ 81.5 ]
3.21
[ 26.1 ]
1.03
[ 51.4 ]
2.02
[ 73.5 ]
2.90
[ 21.5 ]
0.85