User's Manual

ManualsBrandsAndersen ManualsElectronicsIntrusion Detector-400-DH Sensor

Parts Included / Partes Incluidas

(1) Instruction Guide / Instruction Guide

(4) VeriLock Face Plate / VeriLock Face Plate

(1) VeriLock Sensor / VeriLock Sensor

(1) Actuator / Actuator

(2) CR-2032 Battery / CR-2032 Battery

(1) Cylinder Magnet / Cylinder Magnet

(1) Block Magnet / Block Magnet

(2) Cylinder Magnet Cap/ Cylinder Magnet Cap

(2) Block Magnet Cap/ Block Magnet Cap

(2) Screw Standoff / Screw Standoff

(1) 4-1/4" Spindle / 4-1/4" Spindle

(4) #8 x 1-3/4" Bolt (2 white, 2 stone)

(Tribeca® Hardware Only) /

#8 x 1-3/4" Bolt (2 white, 2 stone)

(Tribeca® Hardware Only)

9139831 BA-01 Revised 02/21/16

VeriLock

Security Sensor Application

VeriLock

Security Sensor Application

▶ Read guide from beginning to end before starting installation. Read all warnings and cautions during unit installation.

Lea completamente la guía antes de comenzar la instalación. Lea y respete todas las advertencias y precauciones durante la instalación de la unidad.

▶ Check with your local building code ofcial to identify and conrm compliance with local building code requirements.

Consulte los códigos locales de construcción para identicar y conrmar que se cumplan los requisitos del código de construcción.

Thank you for choosing Andersen. / Gracias por elegir Andersen.

for Andersen

A-Series Frenchwood Hinged Inswing & Outswing, 400 Series Frenchwood

Hinged Inswing &

Outswing and Hinged Inswing & Outswing Entry Doors

for Andersen

A-Series Frenchwood Hinged Inswing & Outswing, 400 Series Frenchwood

Hinged Inswing &

Outswing and Hinged Inswing & Outswing Entry Doors

For questions call 1-888-888-7020. For more information and/or guides visit andersenwindows.com.

Please leave this guide with building owner.

Si tiene alguna pregunta llame al 1-888-888-7020. Para obtener más información y/o guías, visite andersenwindows.com.

Deje esta guía con el dueño de la construcción.

VeriLock®

Face Plate

VeriLock®

Face Plate

VeriLock®

Sensor

VeriLock®

Sensor

Screw Standoff

Block

Magnet

Block

Magnet

Depending on individual installation requirements, some parts may not be used.

Cylinder

Magnet

Cylinder

Magnet

Cylinder

Magnet Cap

Cylinder

Magnet Cap

CR-2032

Battery

CR-2032

Battery

Actuator

Block

Magnet Cap

Block

Magnet Cap

Additional Parts Required for

Entry Doors Only (Ordered Seperately)

Additional Parts Required for

Entry Doors Only (Ordered Seperately)

(1) Extended Lock Actuator /

Extended Accionador del cerrojo

#8 x 1-3/4" Bolt

(Tribeca Hardware Only)

#8 x 1-3/4" Bolt

(Tribeca Hardware Only)

4-1/4"

Spindle

4-1/4"

Spindle

Tools Needed / Herramientas Necesarias

∙ Safety Glasses / Lentes de seguridad

∙ Phillips Screwdriver / Destornillador Phillips

∙ 1/8" Hex Key / Hex Key de 1/8"

∙ Drill/Driver / Taladro/destornillador

∙ 5/16" Drill Bit / Broca para taladro de 5/16"

∙ Tape Measure / Tape Measure

∙ Drop Cloth / Drop Cloth

Summary of content (13 pages)

PAGE 1
VeriLock® Security Sensor Application VeriLock® Security Sensor Application for Andersen® A-Series Frenchwood Hinged Inswing & Outswing, 400 Series Frenchwood® Hinged Inswing & Outswing and Hinged Inswing & Outswing Entry Doors for Andersen® A-Series Frenchwood Hinged Inswing & Outswing, 400 Series Frenchwood® Hinged Inswing & Outswing and Hinged Inswing & Outswing Entry Doors Thank you for choosing Andersen. / Gracias por elegir Andersen. For questions call 1-888-888-7020.
PAGE 2
Use caution when working at elevated heights and around unit openings. Follow manufacturers’ instructions for ladders and/or scaffolding. Failure to do so may result in injury or death. Sea cauteloso al trabajar en lugares elevados y cerca de las aberturas de la unidad. Siga las instrucciones del fabricante para el uso de escaleras y/o andamios. Si no lo hiciera, podrían producirse lesiones o la muerte. Follow manufacturers’ instructions for hand or power tools. Always wear safety glasses.
PAGE 3
1 2 Exterior Handle Manija exterior Interior Interior Set Screw Tornillo de fijación 1/8" Hex Key Hex Key de 1/8" Interior Active Escutcheon Escudete con apertura interior Bushing Casquillo Escutcheon Bolt Perno de escudete Interior Handle Manija interior Bushing Casquillo Spindle Husillo Lay a drop cloth down to prevent losing parts. Unlock and open active door panel. Loosen set screw on exterior handle using 1/8" hex key. Remove handles and set aside for reuse.
PAGE 4
Interior Tribeca® Hardware Only Tribeca® Hardware Only Mounting Stud Mounting Stud Removable Mounting Stud Removable Mounting Stud Screw Standoff Screw Standoff Exterior Active Escutcheon Escudete con apertura exterior Verify gasket is seated properly. Verify gasket is seated properly. Screw Standoff Screw Standoff Exterior Active Escutcheon Escudete con apertura exterior Verify gasket is seated properly. Verify gasket is seated properly.
PAGE 5
7 Interior VeriLock assembly can be rotated for use on either left handed (LH) or right handed (RH) panels. VeriLock assembly can be rotated for use on either left handed (LH) or right handed (RH) panels.
PAGE 6
9 Interior Tribeca® Hardware Only Tribeca® Hardware Only Interior Active Escutcheon Escudete con apertura interior #8 x 1-3/4" Bolt #8 x 1-3/4" Bolt Replace existing bolts with #8 x 1-3/4" bolts. Replace existing bolts with #8 x 1-3/4" bolts. Escutcheon Bolt Perno de escudete Position interior escutcheon on panel as shown and fasten bolts (do not fully tighten until handles have been installed).
PAGE 7
Magnet Application/ Magnet Application Magnets are small parts and, if swallowed, could pose a choking hazard to young children. Los imanes son partes pequeñas que, en caso de ingesta, pueden representar un riesgo de asfixia para niños pequeños. 12 Selection of the correct door configuration is critial for magnet application. Wrong configuration selection will result in improper magent application and product damage. Selection of the correct door configuration is critial for magnet application.
PAGE 8
Viewed from the exterior. For DOUBLE Operating, OUTSWING Doors Only For DOUBLE Operating, OUTSWING Doors Only 12a As viewed from the exterior. As viewed from the exterior. Cylinder Magnet Cap Cylinder Magnet Cap Cylinder Magnet Cylinder Magnet Press cylinder magnet firmly into preferred color cylinder magnet cap. Press cylinder magnet firmly into preferred color cylinder magnet cap.
PAGE 9
For DOUBLE Operating, INSWING Doors Only For DOUBLE Operating, INSWING Doors Only 12b As viewed from the exterior. As viewed from the exterior. FWH 6068 A P L FWH R 9068 S Remove adhesive liner from one side of block magnet and press firmly into ® cap. Frenchwood Left preferred color block magnet adhesive liner from one side of Hinged HingedRemove block magnet and press firmly into Inswing preferred color block magnet cap.
PAGE 10
Viewed from the exterior. For SINGLE Operating, OUTSWING Doors Only For SINGLE Operating, OUTSWING Doors Only 12c As viewed from the exterior. As viewed from the exterior. Cylinder Magnet Cap Cylinder Magnet Cap Cylinder Magnet Cylinder Magnet Press cylinder magnet firmly into preferred color cylinder magnet cap. Press cylinder magnet firmly into preferred color cylinder magnet cap.
PAGE 11
Order Designation Description 12d Viewed from the exterior. For SINGLE Operating, INSWING Doors Only For SINGLE Operating, INSWING Doors Only As viewed from the exterior. As viewed from the exterior.
PAGE 12
Verify VeriLock Sensor Function / Verify VeriLock Sensor Function 13 Thumb Turn Latch Thumb Turn Latch Interior Indicator Light Indicator Light Unlocked Unlocked Locked Locked 1. Close door without locking. Indicator light will illuminate for one (1) second. 2. Engage all upper, middle and lower hooks and lock door with dead bolt. Indicator light will illuminate for one (1) second. Verify door is locked. 3. Unlock door with dead bolt. Indicator light will illuminate for one (1) second. 4. Open door.
PAGE 13
Regulatory Statements / Regulatory Statements Federal Communications Commission (FCC) Part 15 Statement Federal Communications Commission (FCC) Part 15 Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference that may be received, including interference that may cause undesired operation. This device complies with FCC Rules Part 15.