Installation Guide

2
INSTALL
CLOSER
(Images shown are for
a Left Hand installa-
tion. A Right Hand
installation would be
on the opposite side
shown.)
1
1/8”
!
!
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Tools needed:
2”
x 3
x 1
x 2
x 1
x 1
5/8”
1. Open the door and then let it close. Note the speed at which the
door closes.
2. Use a Phillips head screwdriver to adjust the closer to the desired
speed:
For a faster closing speed, turn the adjustment screw to the left
(counterclockwise).
For a slower closing speed, turn the adjustment screw to the
right (clockwise).
3. Test the speed at which the door closes after each adjustment.
1. Attach the jamb bracket arm (L) to the base
by inserting the tabs on the arm into the
slots in the base. Fasten with a 2” screw (N)
from the green bag.
ADJUST
CLOSING
SPEED OF
DOOR
2
Tools needed:
Storm door will close more quickly when entry door is open. To achieve the proper closing speed, you will need to adjust
the closer(s) using the built-in adjustment screw. Check for safe closing speed with your entry door in both the closed and
the open position. To prevent injury, make sure people and/or pets are completely through the opening before allowing
the storm door to shut freely.
WARNING
1. Close the storm door. Swing the closer
assembly over until the door bracket (M) is
resting against the storm door and appears
level. Mark hole locations on the door
frame.
2. Drill holes 5/8” deep and attach the closer
door bracket to the door frame through
the two pre-drilled holes using two (2) 5/8”
screws (O) from the green bag.
Do not drill completely through door. This will create an
unnecessary hole in the door and may cause water and
air inltration.
CAUTION
d
a
c
1. Position the jamb bracket base (K) onto the
door jamb by touching the front of the base
to the back of the hinge rail (or as close as
possible), position and center the base at
least 2 1/2” from the bottom of the door.
Mark the hole locations on the door jamb.
2. Drill holes in the door jamb at the marked
locations and attach the base to the door
jamb with two (2) 2” screws (N) from the
green bag into the two holes closest to the
interior of the house.
M
M
L
J
J
O
O
P
R
1. Pin the closer (J) in place using the short pin
(Q) in the jamb bracket (L) and the long pin
(P) in the door bracket (M).
2. Pull on the closer so the rod extends
slightly. Snap the orange preload clip
from the green bag over the rod. The clip
should be pinched tight between the closer
cylinder body and the jamb bracket.
Q
FRONT VIEWFRONT VIEW
VISTA FRONTALVISTA FRONTAL
VUE AVANTVUE AVANT
HINGE RAILHINGE RAIL
RIEL ABISAGRADORIEL ABISAGRADO
MONTANT À MONTANT À
CHARNIÈRESCHARNIÈRES
K
a
OPPOSITE VIEWOPPOSITE VIEW
OTRO PUNTO DE VISTAOTRO PUNTO DE VISTA
VUE DE FACEVUE DE FACE
L
b
N
N
GREEN BAG / GREEN BAG / BOLSA VERDEBOLSA VERDE / SAC VERT / SAC VERT
ii
VIEWVIEW
ii
VIEWVIEW
ii
VIEWVIEW
ii
VIEWVIEW
ii
VIEWVIEW
!
!
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
1/2”
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
N
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
1/2”
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
O
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
1/2”
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
Q
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
1/2”
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan
P
2 1/2”
R