Instructions / Assembly

ManualsBrandsAndersen ManualsDoors & Windows4000 Series 36 in. x 80 in. Black Right-Hand/Outswing Full View Interchangeable Aluminum Storm Door

Andersen Storm Door Division is a wholly owned subsidiary of Andersen Corporation. Andersen

Storm Door Division manufactures and supports the limited warranties for Andersen® and

EMCO® storm doors. “Andersen” and “EMCO” and all other marks where denoted are trade-

for Andersen® 1-1/2” Fullview Storm Doors

with Standard and Insulating Glass Panels

Installation Guide

Andersen SDD, PO Box 853

Des Moines, IA 50306-0853

Rev 6-2015 14021 Print in Color

Door Frame Assembly:

Rain Cap

Latch Rail

Hinge Rail

Sweep

Handle Clip

Spacer Clips (2)

Bottom Spacer

Glass Panel

Rain Cap Extender

Screw Covers (3)

Not Shown

Handle Set Kit

Installation Kit

Insect Screen

PARTS OVERVIEW

Figure 1

Your installation kit should contain the following

parts. However, in some door models, not all of the

parts will be used.

p/n 624619

Please Do Not Return Product to Store!

with any questions regarding installation, lost part replacement, or anything else related to your storm door purchase.

Read this entire guide before you begin your installation. If your abilities do not

match the requirements of this installation, contact an experienced contractor.

PLEASE call the storm door Solution Center at 1-800-933-3626,

Summary of content (16 pages)

PAGE 1
Installation Guide E for Andersen® 1-1/2” Fullview Storm Doors with Standard and Insulating Glass Panels Please Do Not Return Product to Store! PLEASE call the storm door Solution Center at 1-800-933-3626, with any questions regarding installation, lost part replacement, or anything else related to your storm door purchase. Read this entire guide before you begin your installation. If your abilities do not match the requirements of this installation, contact an experienced contractor.
PAGE 2
SAFETY FIRST: Please read and follow all Cautions and Warnings in this guide. WARNING WARNING Metal fasteners and other hardware components may corrode when exposed to preservative treated and fire-retardant treated lumber. Obtain and use the appropriate size stainless steel fasteners and hardware as called out by the installation guide to fasten unit to any rough opening made from pressure treated and fire-retardant treated lumber.
PAGE 3
INSTALLATION PREPARATION 2 ! Tools needed: ! a X b VIEW RIGHT HANDED A LA DERECHA À MAIN DROITE1/2” LEFT HANDED A LA IZQUIERDA À MAIN GAUCHE 5/8” 2 1/2” 5/8” 1/2” 1/2” Figure 4 40 1/2” TO DOOR SILL HASTA EL BATIENTE DE LA PUERTA JUSQU’AU SEUIL DE LA PORTE Figure 5 1” In this step, you will confirm that your storm door 2” hinges on the correct side. 1 1/2” 1. Left Handed (Figure 4): From the exterior, a left handed storm door will have the handle on the left side of the storm door.
PAGE 4
5/8” 1/2” For a Right Hand Installation, go to Page 10. 3 HANG HINGED STORM DOOR AND REMOVE CLIPS (Left Hand) 5/8” 3/4” Machine Flathead 1/2” F G 1 1/2” H Machine 7/8” Pan Painted A 1/2” Tools needed: 1” SMS Pan1 1/2” X a 1/8” x 20 1” X! b 1” SMS Pan Painted VIEW 1” 2” VIEW 1” Machine Pan Painted c !i VIEW 1-1/2” Machine Flathead 5/8” #10 H 1-1/2” Machine Flathead5/8” 1. Set bottom of door (A) centered in opening. Make sure 1.
PAGE 5
2” /2” 1” Machine 1” Pan Painted SMS Pan Painted 4 i 1-1/2” Machine Flathead 2” #10 VIEW b #12 5/8” SMS Pan Painted #10 3 1 2 1 #12 5/8” SMS Pan Painted 5/8” SMS Pan Painted 1/2” 1/2” 1” clear protective tape from both the interior and exterior of door frame, if applicable. i VIEW 2” SMS Pan Painted #12 1.
PAGE 6
5/8” 5 1/2” 3/4” Machine 9 Flathead INSTALL RAIN CAP, EXTENDER AND SCREW COVERS (Left Hand) 1/2” Tools needed: J K 1” 2” 1 1/2” 7/8” Machine Pan Painted 1/8” 1 1/2” 1” SMS Pan3/16” 12 Plug x1 ! 1” X! 1” SMSbPan Painted X a 13 VIEW B x3 VIEW 1” Machine Pan Painted B 1-1/2” Machine 14 Flathead 5/8” #10 5/8” 1/2” J 1-1/2” Machine Flathead 1. Look at the center hole of the rain cap. If the mounting surface can be 1.
PAGE 7
6 INSTALL THE GLASS PANEL INTO DOOR FRAME (Left Hand) i a VIEW i b VIEW SNUGGER BAR BARRA DE SOPORTE BARRE DE CALAGE 1. Open the door. 2. Push and hold the safety release slide up, then rotate the handle up a 1/4 turn. The handle should now be in a vertical position. VIEW WARNING The glass panel/insect screen is secured in door frame by door handle locking mechanism. Once door handle has been rotated up to vertical position, the glass panel /insect screen are no longer secured in door frame.
PAGE 8
1” SMS Pan Painted ! ! #10 #12 1” Pan 1” SMS Machine Tools needed: INSTALLPan Painted 5/8” 1/2” 7 5/8” 1/2” 1/2” 1/8” 1” Machine Pan Painted 2” SMS Pan Painted x2 #10 1-1/2” Machine Flathead a b 1-1/2” Machine FlatheadVIEW 5/8” SMS Pan Painted B #12i OPPOSITE VIEW OTRO PUNTO DE VISTA VUE DE FACE ! 2” SMS Pan Painted #10 1-1/2” Machine Flathead x6 2” 1 1/2” ! #12 x2 1” 2” 1 1/2” x4 5/8” CLOSERS 5/8” SMS Pan Painted 1-1/2” Machine Flathead M 1” SMS Pan Painted (Left Hand) 1-1/2”
PAGE 9
8 ADJUST CLOSING SPEED OF DOOR Tools needed: 9 FILE EDGE SEAL (Left Hand) Tools needed: Closer and door shown are for reference only. ! ! WARNING WARNING Generously round the bottom corner of the edge seal with a metal file to avoid sharp edges. Failure to round the bottom corners may cause an injury. Storm door will close more quickly when entry door is open. To achieve the proper closing speed, you will need to adjust the closer(s) using the built-in adjustment screw.
PAGE 10
5/8” 1/2” For a Left Hand Installation, go to Page 4. 11 HANG HINGED STORM DOOR AND REMOVE CLIPS (Right Hand) 5/8” 3/4” Machine Flathead 1/2” F G 1 1/2” H Machine 7/8” Pan Painted A 1/2” Tools needed: 1” SMS Pan1 1/2” X a VIEW b 1” SMS Pan Painted 1” Machine Pan Painted 1” 2” 1/8” x 20 1” X! VIEW !i c VIEW 1-1/2” Machine Flathead 5/8” #10 G H 1-1/2” Machine Flathead5/8” 1. Set bottom of door centered in opening. Make sure orange bottom spacer (H) is sitting on door sill. 2.
PAGE 11
2” /2” 1” Machine 1” Pan Painted SMS Pan Painted 1” SMS Pan Painted REMOVE L PROTECTIVE 1-1/2” 1-1/2” Machine Flathead 1” Machine Pan Painted 1” Machine Pan Painted TAPE AND INSTALL HANDLE SET 1-1/2” Machine Flathead 1-1/2” Machine Flathead 1-1/2” (Right Hand) 12 2” #10 VIEW b c #10 Machine Flathead 1-1/2” Machine Flathead 2” SMS Pan1-1/2” Painted #12 2” SMS Pan Painted 5/8” SMS Pan Painted 2 1 3 1 #12 5/8” SMS Pan Painted 5/8” SMS Pan Painted 1/2” 1/2” 1” clear protective tape from
PAGE 12
5/8” 13 INSTALL RAIN CAP MOUNTING FLANGE, SCREW COVERS, & WINDOW RETAINERS (Right Hand) 1/2” 5/8” 3/4” Machine 1/2” 9 Flathead J K 1/2” Tools needed: 1” 7/8” Machine Pan Painted 2” 1 1/2” 1 1/2” 1” SMS Pan 3/16” 12 Plug 1” SMSbPan Painted X a 13 VIEW B x1 1/8” x3 1” ! X VIEW 1” Machine Pan Painted ! B 1-1/2” Machine 14 Flathead 5/8” #10 J 5/8” 1-1/2” Machine Flathead 1/2” 1. Look at the center hole of the rain cap. If the mounting surface can be 1.
PAGE 13
14 HOW TO INSTALL THE GLASS PANEL INTO DOOR FRAME (Right Hand) i a VIEW i b VIEW SNUGGER BAR BARRA DE SOPORTE BARRE DE CALAGE 1. Open the door. 2. Push and hold the safety release slide up, then rotate the handle up a 1/4 turn. The handle should now be in a vertical position. I 1. Orient the glass panel (I) so the notches face the exterior, on the handle side. 2. Slide the glass panel into the door frame on the hinge side first.
PAGE 14
1” SMS Pan Painted ! ! #10 #12 1” Pan 1” SMS Machine Tools needed: INSTALLPan Painted 5/8” 1/2” 15 5/8” 1/2” 1/2” 1/8” 1” Machine Pan Painted 2” SMS Pan Painted x2 x6 2” 1 1/2” #10 x2 1” 2” 1 1/2” x4 5/8” CLOSERS 5/8” SMS Pan Painted 1-1/2” Machine Flathead M 1” SMS Pan Painted (Right Hand) 1-1/2” Machine Flathead 1-1/2” Machine Flathead a b 1-1/2” Machine FlatheadVIEW OPPOSITE VIEW 5/8” SMS Pan Painted OTRO PUNTO DE VISTA B #12 ! #12 2” SMS Pan Painted #10 i ! 1-1/2” Machine Fl
PAGE 15
16 ADJUST CLOSING SPEED OF DOOR 17 Tools needed: FILE EDGE SEAL (Left Hand) Tools needed: Closer and door shown are for reference only. WARNING ! WARNING ! Generously round the bottom corner of the edge seal with a metal file to avoid sharp edges. Failure to round the bottom corners may cause an injury. Storm door will close more quickly when entry door is open. To achieve the proper closing speed, you will need to adjust the closer(s) using the built-in adjustment screw.
PAGE 16
CLEANING INSTRUCTIONS WINDOW GLASS – The glass may be cleaned with any household glass cleaner. Keep glass cleaners away from all other components. PLASTIC PARTS – Plastic door components may be cleaned by using a mild soap and water mixture and by gently rubbing the affected area. Do not use harsh abrasives or any product that contains chlorine. ALUMINUM PARTS – Aluminum parts on the door may be cleaned by using a mild soap and water mixture and by gently rubbing the affected area.