Instructions / Assembly

4
0005519
Fasteners / Sujetadores
Metal fasteners and components may
corrode when exposed to preservative-
treated and/or fire-retardant treated
lumber. Use approved fasteners and
components to fasten unit. Failure to do
so may cause a failure resulting in injury,
property or product damage.
Los componentes y los sujetadores de
metal pueden corroerse cuando quedan
expuestos a madera tratada con retardador
de fuego y con preservante. Utilice los
componentes y/o sujetadores apropiados
para ajustar la unidad. Si esto no se
respeta, se pueden producir lesiones o
daños al producto o a la propiedad.
APPROVED GUSSET PLATE AND CLIP INSTALLATION FASTENER CHART (select one)
TABLA DE BRIDAS Y ABRAZADERAS DE INSTALACIÓN APROBADOS (elija uno)
Fastener Min Shank Min Head Min Length Type of Steel Spacing
Sujetador Espiga min. Cabecera min. Longitud min. Tipo de acero Espacio
galvanized,
zinc plated, ceramic
coated, stainless
every hole
Gusset Plate/
Installation Clip #8 5/16" 1-1/2"
Screw
en cada oricio
Placa de refuerzo/
Abrazadera de instalación #8 5/16" 1-1/2"
Tornillo
galvanizado, cincado,
revestido con cerámica,
inoxidable
Casement (single and double) Head and Sill: None
Sides: On center, at midpoint and 3-1/2" to 4" from each corner, or every hole.
Awning (single) Head and Sill: On center, 3-1/2" to 4" from each corner, or every hole.
Sides: On center, at midpoint.
Awning (double) Head and Sill (minimum): On center, 3-1/2" to 4" from mull post and 3-1/2" to 4" from each end, or every hole.
Sides (minimum): On center, at midpoint.
Awning with Transom Head and Sill: None
Sides: On center, 3-1/2 to 4" from mull post, at midpoint of transom, and 3-1/2" to 4" from each corner, or every hole.
Transom (window or patio door) Head and Sill: None
Sides: On center, at midpoint and 3-1/2" to 4" from each corner, or every hole.
Rectangle (fixed) Head and Sill: None
Sides: On center, at midpoint and 3-1/2" to 4" from each corner, or every hole.
Half Circle (fixed) Sill: On center, 6" from each corner, or every hole.
Curve: On center, 45º from each corner, or every hole.
Quarter Circle (fixed) Each straight side: On center, 6" from each corner, or every hole.
Curve: On center, 30º from each corner, or every hole.
Arch (fixed) Sill: None
Each side: On center, at midpoint and 6" from each corner, or every hole.
Curve: On center, at 1/3 point intervals from each corner, or every hole.
Springline™ (fixed) Sill: None
Each side: On center, at midpoint and 6" from each corner, or every hole.
Curve: On center, 45º from each corner or every hole.
Triangle, Trapezoid, Pentagon, Sill: None
Octagon, Unequal Leg Arch Head: 12" from each corner and center, or every hole.
Each side: 12" from each corner and midpoint, or every hole.
Single-Hung, Single-Hung Arch, Gliding Head and Sill: None
Sides: On center, at midpoint and 3-1/2" to 4" from each corner, or every hole.
Single-Hung with Transom Head and Sill: None
Sides: On center, within 1" to 1-1/2" from check rail, 3-1/2" to 4" from mull post, and 3-1/2" to 4" from each corner, or every hole.
Gliding Below Picture Head and Sill: None
Sides: On center, within 3-1/2" to 4" from mull post, midpoint of fixed, and 3-1/2" to 4" from each corner, or every hole.
APPROVED JAMB INSTALLATION FASTENER CHARTS
Fastener: #8 x 2-1/2" galvanized, zinc plated, ceramic coated or stainless screws (supplied)
Fastener: #8 x 3” galvanized, zinc plated, ceramic coated or stainless screws (supplied)
Product: Spacing:
Product: Spacing: