Instruction Manual

5678
5-2. USB Connector (Type A): BARCODE READER
ڧ Attach a barcode reader or keyboard to send entered text to the counting
scale.
z Transmission system : USB 2.0
z Connector : Type A
z Device class : HID
ڧ Once the device is connected, the color of the LED light changes from
blue to white or yellow.
z
The color does not change if the AD  8561 cannot recognize the connected
device. In this case, restart the AD-8561 and reconnect the device.
z Red LED light blinks when a device of not supported device class is connected.
Note that data may be broken if a USB memory is mistakenly attached.
ڧ Modes and data to transmit *Modes are selectable (Refer to ‘6. Functions’).
z
Key mode: To be used when the counting scale searches/registers an ID or item.
- For searching/registering ID: The last 6 digits of the input data are
recognized as an ID.
- For searching/registering item code: Up to 20 digits from the beginning of
the input data are recognized as an
item code and forward-matching
searching can be done.
z
Command mode: To be used when sending commands to the counting scale
- For commands, refer to the instruction manual for the counting scale.
- Up to 64 digits in a string can be transmitted.
(The data is deleted without being sent if more than 64 digits are input. Restart
the AD-8561 to prevent errors in a subsequent communication data.)
ڧ Caution
z
Barcode reader
Set your barcode reader to add a linefeed code ’Enter’ to the suffix of data.
z
Keyboard
- In command mode, the counting scale cannot recognize the input data
until ’Enter’ key is pressed. Make sure to press ’Enter’ key at the end of
each data entry. Characters are not shown while being entered.
- Re-enter from the beginning if wrong characters are entered.
ڧ Characters that can be entered
z
Numerical: 0 - 9
z Alphabetical: A - Z
(Disable caps lock to enter lower-case letters)
z
Symbols : Refer to the instruction manual of the counting scale for
symbols that can be entered to the device. The keyboard entry is based
on the US keyboard (101 / 104). For the details, please refer to the A&D
website.
5-3. USB Connector (micro B): PC (* AD-8561-MI02 only)
ڧ Communication between the counting scale and a PC via USB interface.
z Transmission system : USB 2.0
z Connector : micro B
z Device class : CDC
z Transmission form: bidirectional communication with virtual COM port
z Data format:
ڧ Supported OS is Windows 7 or later. For the older OS than Windows 10,
a USB driver needs to be installed.
ڧ Install a communication tool such as the WinCT in a PC to connect.
(Refer
to ‘8-2. Related Software’)
5-4. Comparator (Terminal Block):
COMPARATOR (Ͻ AD-8561-MI04 only)
ڧ Relay outputs the comparator result of the counting scale.
ڧ Maximum rating of the relay output
Maximum voltage: 50V DC Maximum current: 100mA DC
Maximum on-resistance: 8 ȍ
ڧ The upper/lower limit values cannot be set with the AD8561. They should
be set with the counting scale.
ڧ Set the function F0610 for the counting scale to ‘1.’
ڧ Pin layout
5-5. Connector for the Counting Scale (D-sub 9 pin):
BALANCE / SCALE
ڧ Performs communication with the counting scale via RS232C interface
z Transmission system and transmission form are same as those
mentioned in ‘5-1. RS-232C Connector (D-sub 9 pin): PRINTER.‘
z Data format:
ڧ Pin layout
ڧ Use the accessory cable (Dsub 9 pin, 1m) to connect it to the counting scale.
ڧ Supply power to AD-8561 from the 9th pin of this connector.
(Refer to ‘4-1. Connection to Power Supply’)
ڧ When operating the function setting for AD-8561 with this connector,
supply power with an AC adapter by connecting to a PC instead of the
counting scale with a crossover cable.
6. Functions
The function setting can be operated with commands.
1. Connect a PC to AD8561 to send commands for the function list.
2. ‘<AK>’ is returned when the setting is saved.
If there is no response, check the communication settings to send commands again.
Response Meaning Action to take
<AK> Saved Restart the device to apply the settings.
EC, E1
Undefined
command
The command is not correct.
EC, E2 Failed
Restart the device and redo the procedures. If
the problem persists, there may be a problem
with the internal circuitry.
Note: When a string that starts with ‘@MI,’ is received, it is recognized as a command
for the AD8561 and the data is not sent to other channels.
3. The communication settings are saved and applied after the AD8561 is
restarted.
Function list ی: Factory settings
Applicable
connectors
Setting details Commands
[PRINTER]
RS232C connector
(Dsub 9 pin)
Baud rate
2400 bps ی @MI024
4800 bps @MI048
9600 bps @MI096
14400 bps @MI144
19200 bps @MI192
28800 bps @MI288
38400 bps @MI384
Data
length
parity
7bit, EVEN ی @MI7EV
7bit, ODD @MI7OD
8 bit, no parity @MI8NO
[BARCODE
READER]
USB connector
(Type A)
HID mode
Key mode ی
(when searching and registering
ID/items with the counting scale)
@MICKM
Command mode
(when sending commands to the
counting scale)
@MICCM
7. Troubleshooting
Phenomenon Possible cause Action to take
LED does not light blue
when power is
supplied.
Poor connection of
power source
Turn on the power to the counting scale. If the
problem persists, switch to an AC adapter for
power supply.
Check the output rating of AC adapter.
Red LED lights Internal circuitry error Restart the device.
LED does not light
white or yellow.
Connection error Check the specifications of the USB device.
When a barcode reader is
connected, the device does
not work.
Insufficient power
supply
Switch to AC adapter for power supply.
Communication fails. Connection Error Check the wiring of connector.
Communication
settings
Reconfirm communication settings are different
for each channel.
The comparator
cannot be input.
Connection error Check the wiring.
The counting scale is not set to comparator output.
8. Specifications and Options
8-1. Specifications
Model AD  8561  MI02 AD  8561  MI04
Power source AC adapter (DC 9 V to 12 V / 500 mA or higher)
Temperature range  10°C to 40°C (No condensation should be observed)
Display (LED) Power on (blue), USB Type A connected (white/yellow), Error (red)
Power consumption Approximately 0.2 VA (when USB Type A is not connected)
Size (W x D x H) 195 × 60 × 40 [mm]
Weight Approximately 190 [g]
Materials Case: ABS, magnets: ferrite, magnet support hole: iron
Items included D  sub 9 pin cable (for connecting the counting scale), instruction manual
Connectable counting scale GC series counting scale (refer to the A&D website)
Connector form Connector for the counting scale/RS  232C: D  sub 9 pin (male)
USB host: Type A
USB function: micro  B Comparator output: terminal (4-pin)
8-2. Related Software
The following software can be downloaded from the A&D website
( https://www.aandd.co.jp/ ).
(1) WinCT (data processing software for balances and scales)
Support > Software > WinCT.
(2) USB driver for AD8561MI02 USB Function
From the products page on the A&D website.
8-3. Optional Devices
(1) AC adapter
Check for the latest adapter in the products page on the A&D website.
(2) Dsub 9 pin cable for connecting the counting scale
Same cable as the accessory
z 1m: AXKO2741100
* If a longer cable is required, a 2-m/5-m cable listed in (3) is usable. However, when
a cable listed in (3) is used, power cannot be supplied from the counting scale.
A separate AC adapter should be connected for power supply.
(3) Dsub 9 pin cable for RS232C
z 2m: AXKO2466200
z 5m: AXKO2466500
* If a 1-m cable is sufficient, the cable mentioned in (2) is usable.
(4) Discrete wire cable for connecting a terminal block
z 2m: AXKO8561N200
(5) USB cable for the AD8561MI02 USB function (micro B -Type A)
z 1.2m: AXTBAMB2A12BK
(6) GC14 (mounting hardware exclusively for GC series counting scales)
(7) AD856111 (a cover for the terminal block on the AD8561MI04)
A&D Company, Limited
3-23-14 Higashi-Ikebukuro, Toshima-ku, Tokyo 170-0013, JAPAN
Telephone: [81] (3) 5391-6132 Fax: [81] (3) 5391-1566
A&D ENGINEERING, INC.
4622 Runway Boulevard Ann Arbor, Michigan 48108, U.S.A.
Telephone: [1] [phone]
A&D INSTRUMENTS LIMITED
Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxfordshire OX14 1DY United Kingdom
Telephone: [44] (1235) 550420 Fax: [44] (1235) 550485
A&D AUSTRALASIA PTY LTD
32 Dew Street, Thebarton, South Australia 5031, AUSTRALIA
Telephone: [61] (8) 8301-8100 Fax: [61] (8) 8352-7409
A&D KOREA Limited ଛ˯߻ࢄ.߽.Ҟ(࣬)
㍲㤎䔏⼚㔲 㡗❇䙂ῂ ῃ㩲⁞㦋⪲ 6 ₎ 33 ( 㡂㦮☚☯ ) ⰾ䞮䌚ア❿ 817 㤆䘎 ⻞䢎 07331
( 817, Manhattan Bldg., 33. Gukjegeumyung-ro 6-gil, Yeongdeungpo-gu, Seoul, 07331 Korea )
㩚䢪 : [82] (2) 780-4101 䕿㓺 : [82] (2) 782-4264
OOO A&D RUS OOO "ɗɃ ɷɧɞ Ⱦɂ Ɋɍɋ"
ɉɨɱɬɨɜɵɣɚɞɪɟɫɊɨɫɫɢɣɫɤɚɹɎɟɞɟɪɚɰɢɹɝɆɨɫɤɜɚɭɥȼɟɪɟɣɫɤɚɹɞɨɦ
ɘɪɢɞɢɱɟɫɤɢɣɚɞɪɟɫɊɨɫɫɢɣɫɤɚɹɎɟɞɟɪɚɰɢɹɝɆɨɫɤɜɚɭɥȾɨɪɨɠɧɚɹɞ
ɤɨɪɩɤɨɦɧɛ
( 121357, Russian Federation, Moscow, Vereyskaya Street 17 )
ɬɟɥ[7] (495) 937-33-  ɮɚɤɫ[7] [phone]
A&D Instruments India Private Limited
( 509, Udyog Vihar, Phase- , Gurgaon - 122016, Haryana, India )
: [91] (124) 4715555 : [91] (124) 4715599
A&D SCIENTECH TAIWAN LIMITED.
A&D⎘䀋↮℔⎠ 刦⬱⼿偉ấ㚱旸℔⎠
⎘㸦⎘⊿ⶪ󰵶㬋⋨曺Ⲟ㜙嶗 5 嘇 4 㦻
( 4F No.5 Ching Tao East Road, Taipei Taiwan R.O.C. )
Tel : [886][phone] Fax : [886][phone]
A&D INSTRUMENTS (THAILAND) LIMITED
¦·¬´ Á° °r ¸ °·¦¼Á¤or (Å¥Â¨r) ε´
168/16 ®¤¼n¸É 1 ε¨¦´· °ÎµÁ£°´»¦¸ ´®ª´»¤µ¸ 12110 ¦³Á«Å¥
( 168/16 Moo 1, Rangsit, Thanyaburi, Pathumthani 12110 Thailand )
Tel : [66] 20038911
Baud rate 19200 bps
Bit length 8 bit
Parity None
Baud rate 19200 bps
Bit length 8 bit
Parity None
AD8561MI02 AD8561MI04
AD8561MI02
AD8561MI04
AD8561MI04
AD8561MI02
AD8561MI02 AD8561MI04
V
cc