Manual

— 19 —
Operation
NOTE: When the hood has been powered up, indicators
are activated and LCD display ON. Indicators turn on for
1 minute then off, the hood is in standby condition. LCD
display OFF automatically after no operations in 1 minute.
a. Once the hood is connected with electricity, if wires for
the control are not well connected, control board is with
QPPSDPOOFDUJPOPSCSFBLEPXOCV[[FSXJMMTPVOECFFQT
You must then disconnect the hood, x the problem and
reconnect the hood.
b. Under any AUTO mode, LCD display OFF automatically
after no operations in 15 seconds.
Lighting
u
Press the light icon one time, turn the lights on and
activates blue indicator.
v
Press the light icon second time, turn the lights off
and indicators off.
To turn auto light sensor on and off (with 4 light settings):
r1SFTTi-uPODF-JHIUTUVSOPOXJUIIJHIMVNJOBODF
Indicator light is off.
r1SFTTi-uOEUJNF-JHIUTUVSOPOXJUIMPXMVNJOBODF
Indicator light is off.
r1SFTTi-uSEUJNF-JHIUTUVSOPOXJUIOJHIUMJHIU
luminance. Indicator light is off.
r1SFTTi-uUIUJNF-JHIUTXJMMXPSLJO"650/*()5
LIGHT mode (working condition controlled by light sensor).
Indicator lights up, you will hear a long audible “beep”.
r1SFTTi-uUIUJNF-JHIUTXJMMUVSOPGGZPVXJMMIFBSBMPOH
audible “beep”.
Cycle is: “high luminance- low luminance- night-
light luminance- AUTO NIGHT-LIGHT- lights off- high
luminance…”
NOTE: When the appliance is in AUTO NIGHT-LIGHT mode,
indicator lights up and you will hear a long “beep” prompt
tone. When light sensor detects the room is dark, lights
will turn on night-light luminance, illuminate icon on LCD
display. When light sensor detects the room is less dark,
night-light will be off automatically, icon is off. And cycle
repeats again and again.
Fan (with 5 speed setting)
u
Press “F” once: Fans work in 1st speed, indicator light
is off, meanwhile illuminate icon on LCD display,
also show digit “1” on screen, indicator light for “”P”
is on.
v
Press “F” 2nd time: Fans work in 2nd speed, show
digit “2” on screen. Indicator light condition remains
the same.
w
Press “F” 3rd time: Fans work in 3rd speed, show
digit “3” on screen. Indicator light condition remains
the same.
x
Press “F” 4th time: Fans work in 4th speed, show digit
“4” on screen. Indicator light condition remains the
same.
y
Press “F” 5th time: Fans work in BOOST mode, show
letter “b” on screen. Indicator light condition remains
the same.
U
Press “F” 6th time: Fans will turn off. Indicator light
condition remains the same. Fan function recycles as
below: “1st speed-2nd speed-3rd speed-4th speed-
Boost speed-0-1st speed…”
NOTE: The appliance will automatically turns to 4 speed
after the Boost speed runs for 2 minutes.
Power
u
Press “P” once, indicator for “”P” lights up and
illuminate icon on LCD display, the hood starts
to work in 1 speed.
v
Press “P” 2nd time, motor will turn off, indicator light
for “”P” and icon on screen will turn off.
NOTE: When motor and lights are working, when you push
“P”, motor and lights will stop working accordingly. Indicator
light for “”P” and icon on screen will turn off. Indicator
lights for “L” will turn off, so do the icons on screen.
Timer
You can only activate TIMER function when motor is
XPSLJOH+VTUXJUIMJHIUTPODBOOPUUVSOPO5*.&3
u
Press “T” button, indicators lights on, you can start
timer setting. Timer is primary set at 3 minutes, use
“F” and “L” to increase or reduce the timer setting
(by minutes). Time setting can be 1-60 minutes.
v
When reach the desired timer setting, push “T”
2nd time to conrm. Then timer will be activated,
countdown will be displayed on the LCD screen.
When “00:00” shows on the screen, motor will turn
off accordingly.
NOTE: 1) Next time you are going to use the timer function,
if press the “T” button and not to adjust the timer setting,
last setting timing will be the default one. Countdown will