V1.00.
FX3000 User's Manual Trademark Information is a registered trademark of OBDSPACE TECHNOLOGY CO., LTD. (ANCEL)in China and other countries. All other ANCEL trademarks, service marks, domain names, logos and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos and company names of or are otherwise the property of ANCEL or its affiliates.
FX3000 User's Manual General Notice • Other product names used herein are for identification purposes only and may be trademarks of their respective owners. ANCEL disclaims any and all rights in those marks. • There is a possibility that this unit is inapplicable to some of the vehicle models or systems listed in the diagnosis section due to different countries, areas, and/or years. Do not hesitate to contact ANCEL if you come across such questions. We are to help you solve the problem as soon as possible.
FX3000 User's Manual • Put the transmission in P (for A/T) or N (for M/T) and make sure the parking brake is engaged. • Keep a fire extinguisher suitable for gasoline/chemical/ electrical fires nearby. • Don’t connect or disconnect any test equipment while the ignition is on or the engine is running. • Keep the FX3000 dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the FX3000, when necessary.
FX3000 User's Manual Table of Contents 1. Introduction..................................................................................................... 1 2. General Information....................................................................................... 1 2.1 On-Board Diagnostics (OBD) II...................................................................... 1 2.2 Diagnostic Trouble Codes (DTCs).................................................................. 2 2.
FX3000 User's Manual 1. Introduction The FX3000 is specially developed by ANCEL, which supports all 10 modes of OBD II test for a complete diagnosis. Featuring the 3.5” TFT color display, it enables users to read/clear DTCs, record, save and playback data in live graphic display. The FX3000 is also very easy to use.
FX3000 User's Manual guide as to where a fault might be occurring within a vehicle. OBD II Diagnostic Trouble Codes consist of a five-digit alphanumeric code. The first character, a letter, identifies which control system sets the code. The second character, a number, 0-3; other three characters, a hex character, 0-9 or A-F provide additional information on where the DTC originated and the operating conditions that caused it to set.
FX3000 User's Manual the DLC cannot be found, refer to the vehicle’s service manual for the location. EN Figure 2-2 2.4 OBD II Readiness Monitors An important part of a vehicle’s OBD II system is the Readiness Monitors, which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system. They are running periodic tests on specific systems and components to ensure that they are performing within allowable limits.
FX3000 User's Manual continuous monitors and are listed below: 1) EGR System 2) O2 Sensors 3) Catalyst 4) Evaporative System 5) O2 Sensor Heater 6) Secondary air Injection 7) Heated Catalyst 8) A/C system 2.5 OBD II Monitor Readiness Status OBD II systems must indicate whether or not the vehicle’s PCM’s monitor system has completed testing on each component. Components that have been tested will be reported as “Ready”, or “Complete”, meaning they have been tested by the OBD II system.
FX3000 User's Manual one or more of vehicle’s systems and may cause emissions to exceed federal standards. If the MIL illuminates with a steady light, it indicates that a problem has been detected and the vehicle should be serviced as soon as possible. Under certain conditions, the dashboard light will blink or flash. This indicates a severe problem and flashing is intended to discourage vehicle operation.
FX3000 User's Manual 3. Product Descriptions 3.1 Outline of FX3000 Figure 3-1 FX3000 Front View No. 6 Name Descriptions 1 OBD-16 connector To connect to vehicle's DLC (Data Link Connector) via diagnostic cable. 2 DTC button To retrieve the DTCs in the database. 3 LCD Indicates test results. 4 Memory card Insert the memory card into it to read or write the slot data/file stored in memory card. 5 USB port To connect on PC to upload data or print test results.
FX3000 User's Manual Up/Down Move cursor up and down for selection. Left/Right Move cursor left or right for selection; Or turn page up and down when more than one page is displayed. 7 OK Confirms a selection (or action) from a menu list. 8 ESC Exit the current program or return to the previous screen. 6 EN 3.2 Specifications • • • • • • Screen: 4.
FX3000 User's Manual 4. Connection 4.1 Install memory card 1) Take out the memory card from package box. 2) Insert the memory card into the FX3000 memory card slot perpendicularly. Make sure is fully inserted in the right place with the “micro” label facing upward. Note: You can hear a clicking sound if you insert the memory card in the right place. Press the card slightly, it will be ejected automatically. 4.2 Connect FX3000 1. Turn the ignition off. 2.
FX3000 User's Manual CAUTION: Don’t connect or disconnect any test equipment with ignition on or engine running. 4.3 Settings Select [Settings] in the main menu and press [OK], the system will enter the following screen: EN Figure 4-2 1) Language This option enables you to set the user interface language. Note: Due to continuous software upgrade, language interface may differ from different software versions. 2) Unit of Measure This option allows you to set measurement unit.
FX3000 User's Manual 5. Diagnose Select [Diagnose] in Main Menu and press [OK], the screen will display Monitor Status interface as following figure 5-1: Figure 5-1 5.1 OBDII/EOBD Diagnosing This option presents a quick way to check for DTCs, isolate the cause of the illuminated Malfunction Indicator Lamp (MIL), check monitor status prior to emissions certification testing, verify repairs, and perform a number of other services that are emission-related.
FX3000 User's Manual EN Figure 5-4 It mainly includes the following functions: Follow the on-screen instructions to check the possible cause and retry it. 1. Read Codes This option is used to identify which section of the emission control system has malfunctioned. 2. Erase Codes After reading the retrieved codes from the vehicle and certain repairs have been carried out, you can use this function to erase the codes from the vehicle.
FX3000 User's Manual The I/M Readiness Monitor Status function also can be used (after repair of a fault has been performed) to confirm that the repair has been performed correctly, and/or to check for Monitor Run Status. 4. Data Stream This option retrieves and displays live data and parameters from the vehicle’s ECU. 5. View Freeze Frame When an emission-related fault occurs, certain vehicle conditions are recorded by the on-board computer. This information is referred to as freeze frame data.
FX3000 User's Manual 5.2 System Diagnosing This function is specially designed to diagnose electronic control system of single vehicle model which includes the following systems: • ENG (Engine) • ABS (Anti-lock Brake System) • TCM (Transmission Control Module) • SRS (Supplemental Restraint System) EN Notes: • Before diagnosing, please make sure the diagnostic program corresponding to certain vehicle model has been installed on your FX3000.
FX3000 User's Manual 5.3 Review This function is used to review or delete the recorded DTC, Data Streams and Freeze Frame. 5.4 Resetting In addition to amazing & powerful diagnostic function, FX3000 also features Oil lamp reset, Electronic parking brake reset, Steering angle calibration, ABS Bleeding and Battery maintenance system reset. There are two methods to reset service lamp: Manual reset or Auto reset.
FX3000 User's Manual 6. Help This menu enables you to view device information and OBD introduction. In main menu, select [Help] and press [OK] to enter Figure 6-1. EN Figure 6-1 6.1 DLC Location Information This option helps you to find the location of the vehicle’s DLC. 6.2 DTC Library In Figure 6-1, select [DTC Library] and press [OK] to enter the following screen. Figure 6-2 Press [ ]/[ ] button to move the highlight bar to different position.
FX3000 User's Manual 6.3 Abbreviation This option allows you to view the full name and detailed explanation of the automotive glossary abbreviations. 6.4 Tool Information In Figure 6-1, select [Tool Information] and press [OK] to view the related information of FX3000. Figure 6-3 Note: You are strongly recommended to note down the Serial Number and Register Code in Figure 6-3 since these 2 pieces of information are required while registering your FX30000. Press [ESC] to return to the previous screen. 6.
FX3000 User's Manual 7. Register & Update Hardware Requirement: 1. A computer that can access the Internet. 2. A memory card reader/writer and a memory card that need to be updated. There are 2 methods available: via memory card or via USB cable. Here we take memory card for example to demonstrate how to update your tool: 1. Go to http://www.anceltech.com and click “Download” --> “FX3000”, then click updating icon. 2. Download and install the update tool and launch the program when installed. 3.
FX3000 User's Manual [OK] button. (Figure 7-3) Figure 7-3 7. Select [Tool Information], press [OK]. (Figure 7-4) Figure 7-4 8. This is the Register Code number for inputting into step 4 (Figure 7-5).
FX3000 User's Manual Figure 7-5 (Return to step 4 and input the code and then proceed) 9. Install the memory card from the tool into the supplied card adapter and insert into USB port of CPU. 10.Reopen the FX3000 update Suite and select the updates you would like to perform or click [Select All] and click [Download]. (Figure 7-6) EN Figure 7-6 11.Once all steps are complete, reinsert the memory card into the tool and power the tool via USB in computer or via OBD2 port in vehicle.
FX3000 User's Manual 8. FAQ Here we list some frequently asked questions and answers relating to FX3000. Question: System halts when reading data stream. What is the reason? Answer: It may be caused by a slackened connector. Please turn off the FX3000, firmly connect the connector, and switch it on again. Question: Screen of main unit flashes at engine ignition start. Answer: Caused by electromagnetic disturbing, and this is normal phenomenon.
FX3000 User's Manual Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE ANCEL PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER’S BUSINESS. ANCEL electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user.
Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO PERSONS WHO PURCHASE ANCEL PRODUCTS FOR PURPOSES OF RESALE OR USE IN THE ORDINARY COURSE OF THE BUYER’S BUSINESS. ANCEL electronic product is warranted against defects in materials and workmanship for one year (12 months) from date of delivery to the user.
