User Guide

ManualsBrandsAnbull ManualsAir Compressors & InflatorsGX E-5K2 PCP Air Compressor, 4500psi 110V 1200W, Auto-Stop Setting, 2 Pistons & 4 Stages Compression, Water and Fan Cooling, Moisture Filter,10 Hours Continuous Work for Paintball,Scuba Dive Tank

Operating Instruction of New Model High Pressure Aerator

Thank you very much for choosing us. The new and good-looking machine will bring you a very

safe, quiet and clean working environment. Meanwhile, Our team will provide you with the best

service. When you opening the box, please check whether the accessories are complete against the

packing list. if you have any questions, please contact your sales manager timely to reduce your loss.

Summary of content (10 pages)

PAGE 1
Operating Instruction of New Model High Pressure Aerator Thank you very much for choosing us. The new and good-looking machine will bring you a very safe, quiet and clean working environment. Meanwhile, Our team will provide you with the best service. When you opening the box, please check whether the accessories are complete against the packing list. if you have any questions, please contact your sales manager timely to reduce your loss.
PAGE 2
Packing list 1 Manual 1 pc 2 Power Cord 1 pc( Please make sure if the power plug is suitable for local outlet) 3.High Pressure Outlet Hose 1 pc ( Quick connector is available on 2 ends. Testing Plug is on 1 end.) 4.High Pressure Pumps 1 unit 5. Maintain tooling and accessories; Spare parts list: Serial No. 1 2 Name Face spanner 10x14x19Box Spanner Serial No. 11 12 Name S8 Hex key spanner Outer dia.30*1.
PAGE 3
spanner 5 12-14O pen-end spanner rings 15 40 outer piston rings plate 25 2nd level pistion spring Outer 6 screwdriver 16 dia.16*1.8sealing 26 anti bursting film ring Outer dia 7 Needle grease 17 16*1.5sealing 27 ring 8 9 10 S2 hex key spanner S2.5 Hex key spanner S5 Hex key Machine Parameter: 1，Model:GX-4*2E-110 2，Power supply: 110V 60HZ 3，Power:1.2KW 4，Max current:13A hours 5，Weight: 6，Operating noise:64-72db 18 19 20 6mm inner sealing sleeve Outer dia.10.*1.
PAGE 4
high-pressure outlet , start the machine and run for 5 minutes. Connect the quick joint of the high pressure hose to the high pressure outlet of the machine, screw and close the vent valve while the machine is running, and observe the pressure gauge. It is normally takes 20 seconds from 0 to 4500Psi. If more than 25 seconds or the pointer hovers in a certain range, there is a possibility of air leakage.
PAGE 5
Please twist grease injector for 1 bar after machine working for 4 to 6 hours .If inject too much grease it would be affect the quality of the gas. VII: Frequently questions and solution: 1. Plug in the power toggle switch but the indicator light of the machine is not on, and it will not start.--------As the pin plug is a standard part, you can use other electrical appliances with the pin plug to test whether the cable is in good condition.
PAGE 6
Se Ser ial ri Name No. al Ser Name No ial Ser Name No. ial Name No. . outer 1 Back side panel 42 dia.30*1.5sealing 83 ring 2 3 1st level cylinder sleeve Tracheal tube 43 44 2nd level piston spring base Wave spring 84 85 6mm inner sealing sleeve sealing base locating pad outer dia.16*1.
PAGE 7
ring 4 5 2nd level cylinder sleeve 3 rd level cylinder sleeve 45 40taper washer 86 Sealing socket 127 baseboard 46 40conical washer 87 High pressure rod 128 wheel 2nd level piston 88 6 Oil cylinder screw 47 7 Oil cylinder 48 8 9 10 11 Oil cylinder spring 2nd level piston spring 89 49 4mm steel ball 90 50 piston Outer dia.
PAGE 8
washer dia.40*2sealing ring 23 4mm steel ball 64 33inner piston ring 105 M6*130 inner hex socket screw outer 146 dia.9*1.5sealing ring outer 24 4.2*15 spring 65 33taper washer 106 dia.8.8*1.5sealing 147 filter tube ring 25 26 12mm complex washer output connector 66 67 wave spring dead plate pressure ring 107 M6flat washer 148 filter board 108 Connecting rod 149 wool pad outer 27 Connector PL8-01 68 dia.45*2sealing 109 ring outer 28 M8 cap nut 69 dia.
PAGE 9
39 water location pin 80 sealing base spring 121 conversion shaft 162 122 Two stage crankcase 163 outer 40 high pressure tube 81 dia.10*1.
PAGE 10