Owner's manual

9►[CONTROL] + ENTER.
9-1 [Versions] + ENTER.
Version _._= update version.
 I1toI4=Identicationnumber.
 K,A,B,C,O=statusoftheinternalrmwareversions.
9-2 [Transition] + ENTER.
 Selectanitemwith◄►+ENTER
9-2-1 [Fade color] + ENTER.
This function allows selecting the color of the frame during the fade through frame transition. Select
acolor(red,greenandblue)with◄►+ENTERandadjustthelevelwith◄►+ENTER. During the
adjustment the color is displayed on the output. To obtain black, set the 3 levels to minimum. To obtain
white, set the 3 levels to maximum. To obtain grey, set the 3 levels in the middle.
9-2-2 [Clean cut] + ENTER.
This function allows a clean switching thanks to a fast freeze of the displayed source. Select a function
with◄►+ENTER.
  •[fromcomputer]:TheCLEANCUToperatesonlywhenswitchingfromacomputersource.Switching
from the source operates with a fade color.
  •[fromvideo]:TheCLEANCUToperatesonlywhenswitchingfromavideosource.Switchingfromthe
source operates with a fade color.
  •[fromall]:TheCLEANCUToperateswhenswitchingfromanysource.
9-2-3 [Fade frame] + ENTER.
This function allows switching by a fading through a frame (instead of a color). Select a frame and adjust
thedurationofthetransitionwith◄►+ENTER.
9-3 [Sync loss] + ENTER.
 Allowstodisplayaframeorasourceincaseofsync-lossoftheselectedinput.Selectanitemswith◄►+ENTER
9-4 [RS232/LAN port] + ENTER.
 Selectthecommunicationportwith◄►+ENTER.
• [RS232] : Enables the RS-232 communication port. (Default setting).
• [LAN]: EnablestheLANcommunicationport.
IMPORTANT : To avoid address conicts, congure the LAN communication port (with the LAN setup
menu) before activating it.
NOTE : The RS-232 & the LAN communication ports can not be used simultaneously.
9-5 [LAN setup] + ENTER.
 AllowsconguringtheLANcommunicationport.SelecttheUDPorTCPprotocolwith◄►+ENTER then select
itemswith◄►+ENTER.
• [device addr.] : Every device connected to an IP network must have a unique IP address. This address is used
toreferencethespecicunit.IPaddressesarespeciedasx.x.x.xwhereeachxisanumber
from1to254.AssignthedevicetoauniqueIPaddresswith◄►+ENTER. (Default value:
192.168.0.2).
• [remote addr.] : This is the destination IP address used with an outgoing connection. Select the destination IP
addresswith◄►+ENTER.(Defaultvalue:192.168.0.1).
• [gateway addr.] :Thegatewayaddress,orrouter,allowscommunicationwithotherLANsegments.Thega-
tewayaddressshouldbetheIPaddressoftherouterconnectedtothesameLANsegment
astheunit.Selectthegatewayaddresswith◄►+ENTER.(Defaultvalue:192.168.0.1).
• [device port] :EveryTCPconnectionandeveryUDPdatagramisdenedbyadestinationIPaddressanda
portnumber.Selectalocalportnumberwith◄►+ENTERbetween10000and10999.(De-
faultvalue:10500).
• [remote port] : You must set the remote TCP port number for the unit to make outgoing connections. This pa-
rameterdenestheportnumberonthetargethosttowhichaconnectionisattempted.Select
aremoteportnumberwith◄►+ENTERbetween00000and655000.(Defaultvalue:10500).
• [netmask] : AnetmaskdenesthenumberofbitstakenfromtheIPaddressthatareassignedforthehost
section. The device prompts for the number of host bits to be entered, then calculates the
netmask, which displays in standard decimal-dot notation when the saved parameters are dis-
played.Selectthenetmaskwith◄►+ENTER.(Defaultvalue:255.255.255.0).
• [default setup] :SetalltheLANsettingstodefaultvalue.Select[YES]andvalidatewithENTER.
PAGE 35