Datasheet

SW06
REV. A
–3–
ELECTRICAL CHARACTERISTICS
SW06B SW06F SW06G
Parameter Symbol Conditions Min Typ Max Min Typ Max Min Typ Max Units
TEMPERATURE RANGE T
A
Operating –55 +125 –25 +85 0 70 °C
“ON” RESISTANCE R
ON
V
S
= 0 V, I
S
= 1.0 mA 75 110 75 125 75 175 Ω
V
S
= ±10 V, I
S
= 1.0 mA 80 110 80 125 80 175
∆R
ON
MATCH BETWEEN SWITCHES R
ON
Match V
S
= 0 V, I
S
= 100 µA
1
6 20 6 25 10 %
ANALOG VOLTAGE RANGE V
A
I
S
= 1.0 mA
2
+10 +11 +10 +11 +10 +11 V
I
S
= 1.0 mA
2
–10 –15 –10 –15 –10 –15
ANALOG CURRENT RANGE I
A
V
S
= ±10 V 7 12 5 11 11 mA
∆R
ON
WITH APPLIED VOLTAGE ∆R
ON
–10 V ≤ V
S
≤ 10 V, I
S
= 1.0 mA 10 12 15 %
SOURCE CURRENT IN V
S
= 10 V, V
D
= –10 V
“OFF” CONDITION I
S(OFF)
T
A
= Max Operating Temp
3, 9
60 30 60 nA
DRAIN CURRENT IN V
S
= 10 V, V
D
= –10 V
“OFF” CONDITION I
D(OFF)
T
A
= Max Operating Temp
3, 9
60 30 60 nA
LEAKAGE CURRENT IN I
S(ON)+
V
S
= V
D
= ±10 V 100 30 60 nA
“ON” CONDITION I
D(ON)
T
A
= Max Operating Temp
3, 9
LOGICAL “1” INPUT CURRENT I
INH
V
IN
= 2.0 V to 15.0 V
5
10 10 15 µA
LOGICAL “0” INPUT CURRENT I
INL
V
IN
= 0.8 V 4 10 4 10 5 15 µA
TURN-ON TIME t
ON
See Switching Time 440 900 500 900 1000 ns
Test Circuit
4, 8
TURN-OFF TIME t
OFF
See Switching Time 300 500 330 500 500 ns
Test Circuit
4, 8
BREAK-BEFORE-MAKE TIME t
ON
–t
OFF
Note 7 70 70 50 ns
POSITIVE SUPPLY CURRENT I+ All Channels “OFF,” 9.0 13.5 13.5 mA
DIS = “0”
3
NEGATIVE SUPPLY CURRENT I– All Channels “OFF,” 7.5 10.5 10.5 mA
DIS = “0”
3
GROUND CURRENT I
G
All Channels “ON” or 6.0 7.5 7.5 mA
“OFF”
3
NOTES
(@ V+ = +15 V, V– = –15 V, –558C ≤ T
A
≤ +1258C for SW06BQ, –408C ≤ T
A
≤ +858C for
SW06FQ and –408C ≤ T
A
≤ +858C for SW06GP/GS, unless otherwise noted)
1
V
S
= 0 V, I
S
= 100 µA. Specified as a percentage of R
AVERAGE
where: R
AVERAGE
=
R
ON1
+ R
ON2
+ R
ON3
+ R
ON4
4
.
2
Guaranteed by R
ON
and leakage tests. For normal operation maximum analog signal voltages should be restricted to less than (V+) –4 V.
3
Switch being tested ON or OFF as indicated, V
INH
= 2.0 V or V
INL
= 0.8 V, per logic truth table.
4
Also applies to disable pin.
5
Current tested at V
IN
= 2.0 V. This is worst case condition.
6
Sample tested.
7
Switch is guaranteed by design to provide break-before-make operation.
8
Guaranteed by design.
9
Parameter tested only at T
A
= +125°C for military grade device.
Specifications subject to change without notice.