Datasheet

For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: [phone] Fax: [phone] Order On-line at www.hittite.com
Application Support: Phone: [phone] or [e-mail]
POWER CONDITIONING - SMT
2
HMC1060LP3E
v00.1211
QUAD LOW NOISE HIGH PSRR
LINEAR VOLTAGE REGULATOR
Electrical Specications
T
A
= +25 °C, VDD = 5.6 V, Unless Otherwise Specied, PTAT Mode is disabled, measured at maximum load conditions
in default conguration as shown in Application Schematic.
Parameter Conditions Min Typ Max Units
Output Voltage on All Outputs 1.8 5.2 V
Default Output Voltage VR1, VR2, VR3
Default Conguration shown in Application
Schematic
3.24 3.3 3.36 V
Default Output Voltage VR4 4.9 5.0 5.1 V
Output Voltage Tolerance
[1]
PTAT Mode Disabled 2 %
PTAT Mode Enabled 3 %
Input Voltage Range (Default) 5.3 5.6 V
Input Voltage Range
[2]
3.35
Max (VRx) +
0.3 V
5.6 V
Output Current VR1
[3]
T
A
= -40 °C to +85 °C 100 mA
Output Current VR2, VR3
[3]
T
A
= -40 °C to +85 °C 50 mA
Output Current VR4
[3]
T
A
= -40 °C to +85 °C 300 mA
Total Output Current T
A
= -40 °C to +85 °C 500 mA
Output Noise Voltage Density
10 Hz
100 Hz
1 kHz
10 kHz
100 kHz
2200
120
7
3
3
nV/√Hz
Integrated Output Noise 100 Hz to 100 kHz 1.5 µVrms
Load Regulation, VR4 0 to 300 mA 0.007 % / mA
VR1 PSRR
1 kHz
10 kHz
100 KHz
1 MHz
10 MHz
80
80
72
60
52
dB
Current Consumption (I
GND
)
VEN = VDD = 5.6 V;
Maximum Load Current
2.1 mA
Power Down Current
VEN = Low; VRx outputs are oating (high
- impedance) in Power-Down Mode
1 2 µA
Start-Up Transient Time
0 to 90% of nal voltage;
EN connected to VDD
50 ms
EN Turn-On Delay
0 to 90% of nal output voltage
Cref = 4.7 µF; Cload = 10 µF; VDD = 5.6
VEN transition from 0 to VDD
30 ms
Enable Input EN High Level 2 VDD + 0.3 V
Enable Input EN Low Level 0 0.8 V
Thermal Protection Threshold Junction
Temperature
No loads 150 °C
Maximum Dissipated Power All Outputs Loaded 1.6 W
[1] When using external resistors to congure the HMC1060LP3E outputs to non-default levels, the temperature coefficient of external resistors
may increase the output voltage tolerance. Note that internal resistors have a temperature coefficient of +270 ppm/°C.
[2] Minimum input voltage (VDD) is dened by maximum desired output voltage. As an example minimum input voltage (VDD) of 4.3 V is required
to set the HMC1060LP3E outputs as follows VR1 = VR2 = VR3 = 3.3 V, VR4 = 4 V.
[3] The outputs will withstand short-circuit conditions for a duration of less than 10 seconds.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: [phone] • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.