Camera EI3 Extender Board Manual an EZ-Extender® product Revision 1.0, August 2012 Part Number 82-000351-01 Analog Devices, Inc. One Technology Way Norwood, Mass.
Copyright Information ©2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written consent from Analog Devices, Inc. Printed in the USA. Disclaimer Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable.
Regulatory Compliance The Camera EI3 Extender Board is designed to be used solely in a laboratory environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity. This board should not be used in or near any medical equipment or RF devices.
CONTENTS PREFACE Product Overview ........................................................................ vii Purpose of This Manual .............................................................. viii Intended Audience ...................................................................... viii Manual Contents .......................................................................... ix What’s New in This Manual .......................................................... ix Technical Support .....
Contents Expansion Interface III ................................................................. 1-5 Example Programs ........................................................................ 1-6 Board Design Database ................................................................. 1-6 CAMERA EI3 EXTENDER BOARD HARDWARE REFERENCE System Architecture ...................................................................... 2-2 Jumpers .........................................................................
PREFACE Thank you for purchasing the Camera EI3 Extender Board, an EZ-Extender® product for EZ-KIT Lite®/EZ-Board® evaluation systems with the expansion interface 3 (EI3). The EZ-KIT Lite/EZ-Board and Camera EI3 Extender Board are designed to be used in conjunction with the CrossCore® Embedded Studio (CCES) development environment. To learn more about Analog Devices development software, go to http://www.analog.com/dsp/tools.
Purpose of This Manual The following is a list of the Camera EI3 Extender Board interfaces.
Preface Programmers who are unfamiliar with Analog Devices processors can use this manual, but should supplement it with other texts that describe your target architecture and hardware development tools. Programmers who are unfamiliar with the CrossCore Embedded Studio programming environment or the mating evaluation board should refer to the CCES online help. Manual Contents The manual consists of: • Chapter 1, “Using Camera EI3 Extender Board” on page 1-1 Provides basic product information.
Technical Support Technical Support You can reach Analog Devices processors and DSP technical support in the following ways: • Post your questions in the processors and DSP support community at EngineerZone®: http://ez.analog.com/community/dsp • Submit your questions to technical support directly at: http://www.analog.com/support • E-mail your questions about processors, DSPs, and tools development software from CrossCore Embedded Studio or VisualDSP++®: Choose Help > Email Support.
Preface • Send questions by mail to: Processors and DSP Technical Support Analog Devices, Inc. Three Technology Way P.O. Box 9106 Norwood, MA 02062-9106 USA Supported Products This extender board supports EZ-KIT Lite/EZ-Board evaluation systems with the expansion interface 3. Product Information Product information can be obtained from the Analog Devices Web site and the CCES online help system. Analog Devices Web Site The Analog Devices Web site, www.analog.
Product Information about products you are interested in. You can choose to receive weekly e-mail notifications containing updates to the Web pages that meet your interests, including documentation errata against all manuals. myAnalog provides access to books, application notes, data sheets, code examples, and more. Visit myAnalog (found on the Analog Devices home page) to sign up. If you are a registered user, just log on. Your user name is your e-mail address.
Preface Related Documents For additional information about the processor, refer to the following publications. Table 1.
Related Documents xiv Camera EI3 Extender Board Manual
1 USING CAMERA EI3 EXTENDER BOARD This chapter provides the setup procedure for the Camera EI3 Extender Board and describes the interfaces the extender supports. The information is presented in the following order.
Package Contents Package Contents Your Camera EI3 Extender Board package contains the following items. • Camera EI3 Extender Board • A bag containing hardware for securing the extender board on the EZ-KIT Lite/EZ-Board • Release note containing information about the product download Contact the vendor where you purchased your extender board or contact Analog Devices, Inc. if any item is missing.
Using Camera EI3 Extender Board System Requirements Verify that your PC has these minimum requirements for the CCES installation: • 2 GHz single-core processor • 1 GB RAM • 8 GB available disk space • One open USB port A faster disk drive decreases the build time, especially for a large amount of source files. Camera EI3 Extender Board Installation Follow these instructions to ensure correct operation of the product hardware and software. 1. Attach the extender board to the EZ-KIT Lite/EZ-Board.
Aptina CMOS Sensor Interface 4 4 4 5 4 3 2 5 EZ-Extender 3 (Stacked) 2 1 2 Item Part Description 1 0.75in Nylon Standoff 2 1.0in Nylon Standoff 3 1.25in Nylon Standoff 4 Nylon Screw 5 Nylon Spacer 1 Figure 1-1. Assembled Board Diagram Aptina CMOS Sensor Interface The Camera EI3 Extender Board supports interfacing with Aptina CMOS sensor headboards that have an 8-, 10- or 12-bit interface. Both image processors/SOC and sensor headboards are supported.
Using Camera EI3 Extender Board An example program demonstrating capabilities via a M114 headboard is available by installing the Camera EI3 Extender Board Support Package (BSP). The headboard can be purchased through C4AV.com using part number MT9M114EBLSTCZH ES. Expansion Interface III The Expansion Interface III (EI3) allows an extender board to be tested across various hardware platforms that have the same expansion interface connectors.
Example Programs If more current is required, then a separate power connector and a regulator must be designed on the daughter card. Additional circuitry can add extra loading to signals, decreasing their maximum effective speed. Devices does not support and is not responsible for the Analog effects of additional circuitry. Example Programs Example programs are included with the Camera EI3 Extender Board Support Package (BSP). Example programs demonstrate various capabilities of the product.
2 CAMERA EI3 EXTENDER BOARD HARDWARE REFERENCE This chapter describes the hardware design of the Camera EI3 Extender Board. The following topics are covered. • “System Architecture” on page 2-2 Describes the daughter board configuration and explains how the board components interface with the processor and EZ-KIT Lite. • “Jumpers” on page 2-3 Describes jumper functionality. • “Connectors” on page 2-4 Shows the locations and provides part numbers for the on-board connectors.
System Architecture System Architecture A block diagram of the Camera EI3 Extender Board is shown in Figure 2-1. TWI PPI Figure 2-1.
Camera EI3 Extender Board Hardware Reference Jumpers This section describes jumper functionality. The jumper on the Camera EI3 Extender Board is located on the back of the board. Camera Width Jumper (JP1) The camera width jumper (JP1) determines whether the interface to the processors PPI is 8, 10 or 12 bits. The camera width is chosen by placing the jumper in the appropriate position. By default, 8-bit mode is selected since that is the interface that is on the M114 headboard.
Connectors Connectors This section describes connector functionality and provides information about mating connectors. Figure 2-2 shows the locations of all connectors on the Camera EI3 Extender Board. Figure 2-2.
Camera EI3 Extender Board Hardware Reference Expansion Interface III (EI3) Connector (J1) One board-to-board connector (J1) provides signals from the PPI and TWI ports of the processor. The connector is located on the top side of the board. Part Description Manufacturer Part Number 120-pin, 0.6 mm HIROSE FX8-120S-SV(21) Mating Connector 120-pin, 0.
Connectors Power Connector (P4) Under normal circumstances, the power connector is not needed because the Camera EI3 Extender Board derives its power from the EZ-KIT Lite/EZ-Board. If the EZ-KIT Lite/Camera EI3 Extender Board is not able to supply enough power to the Camera EI3 Extender Board, then an external power supply can be connected to P4 which will power the Camera EI3 Extender Board and EZ-KIT Lite/EZ-Board. The connector is located on the bottom side of the board.
A CAMERA EI3 EXTENDER BOARD BILL OF MATERIALS The bill of materials corresponds to “Camera EI3 Extender Board Schematic” on page B-1. Ref. Qty. Description Reference Designator Manufacturer Part Number 1 1 27MHZ OSC003 U4 EPSON SG-8002CA-MP 2 3 SN74LVC16T245 TVSOP48 U1-U3 DIGI-KEY 296-21052-1-ND 3 1 PWR .65MM CON027 P4 DIGI-KEY CP1-022PJCT-ND 4 1 1A RESETABLE 1206 F1 RAYCHEM NANOSMDC110F-2 5 1 IDC 3X2 IDC3X2 JP1 BURG 54102-T08-03LF 6 1 .
A-2 Camera EI3 Extender Board Manual
A B D C 1 1 Camera EI3 Extender Board SCHEMATIC 2 2 3 3 ANALOG DEVICES 4 Board No. A B C 4 PH: 1-800-ANALOGD Rev A0351-2012 C Date Nashua, NH 03063 Camera EI3 Extender Board Title Sheet Title Size 20 Cotton Road 0.
A B D C J1 PPI_CLK PPI_FS2 PPI_D0 PPI_D2 PPI_D4 PPI_D6 PPI_D8 PPI_D10 1 94 PPI0_CLK 95 PPI0_FS2 101 PPI0_D0 102 PPI0_D2 103 PPI0_D4 105 PPI0_D6 106 PPI0_D8 107 PPI0_D10 108 PPI0_D12 12 PPI0_D14 111 PPI0_D16 112 PPI0_D18 113 PPI0_D20 114 PPI0_D22 27 PPI0_FS1 PPI_FS1 26 PPI0_FS3 20 PPI0_D1 PPI0_D3 19 18 PPI0_D5 PPI0_D7 16 15 PPI0_D9 PPI0_D11 14 PPI_D1 PPI_D3 PPI_D5 PPI_D7 PPI_D9 VIN USB_VCC PWR_IN VCC PPI_D11 1 13 PPI0_D13 110 D3 10 MBR130LSFT1G SOD-123FL
A B 1 3.3V 3.
I INDEX A E Aptina CMOS sensor interface, 1-4 architecture, of Camera EI3 Extender Board, 2-2 assembled board diagram, 1-4 EngineerZone, xii expansion interface III (EI3) connector (J1), 2-5 overview, 1-5 extender board block diagram, 2-2 B bill of materials, A-1 block diagram assembled board, 1-4 Camera EI3 Extender Board, 2-2 board design, 1-6 board schematic (Camera EI3 Extender Board), B-1 C camera width jumper (JP1), 2-3 connectors, 2-4 diagram of locations, 2-4 IDC, 2-5 J1 (EI3), 2-5 J2 (sensor
Index R related documents, xiii S schematic, of Camera EI3 Extender Board, B-1 sensor connector (J2), 2-5 sensor connector (J3), 2-5 supported operating systems, 1-2 supported products, xi system architecture, 2-2 system requirements, 1-3 T technical support, x I-2 Camera EI3 Extender Board Manual
