Datasheet
Table Of Contents
- FEATURES
- APPLICATIONS
- GENERAL DESCRIPTION
- REVISION HISTORY
- INTRODUCTION
- FUNCTIONAL BLOCK DIAGRAM
- SPECIFICATIONS
- ABSOLUTE MAXIMUM RATINGS
- PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
- ANALOG FRONT END
- ANALOG INPUT MUXING
- MANUAL INPUT MUXING
- XTAL CLOCK INPUT PIN FUNCTIONALITY
- 28.63636 MHz CRYSTAL OPERATION
- ANTIALIASING FILTERS
- SCART AND FAST BLANKING
- FAST BLANK CONTROL
- FB_MODE [1:0], Address 0xED [1:0]
- Static Mux Selection Control
- Alpha Blend Coefficient
- Fast Blank Edge Shaping
- Contrast Reduction
- Contrast Reduction Enable
- Contrast Mode
- Fast Blank and Contrast Reduction Programmable Thresholds
- FB_INV, Address 0xED [3], Write Only
- Readback of FB Pin Status
- FB Timing
- Alignment of FB Signal
- Color Space Converter Manual Adjust
- GLOBAL CONTROL REGISTERS
- STANDARD DEFINITION PROCESSOR (SDP)
- SD LUMA PATH
- SD CHROMA PATH
- SYNC PROCESSING
- VBI DATA RECOVERY
- GENERAL SETUP
- Video Standard Selection
- Autodetection of SD Modes
- VID_SEL [3:0], Address 0x00 [7:4]
- AD_SEC525_EN, SECAM 525 Autodetect Enable, Address 0x07 [7]
- AD_SECAM_EN, SECAM Autodetect Enable, Address 0x07 [6]
- AD_N443_EN, NTSC 443 Autodetect Enable, Address 0x07 [5]
- AD_P60_EN, PAL 60 Autodetect Enable, Address 0x07 [4]
- AD_PALN_EN, PAL N Autodetect Enable, Address 0x07 [3]
- AD_PALM_EN, PAL M Autodetect Enable, Address 0x07 [2]
- AD_NTSC_EN, NTSC Autodetect Enable, Address 0x07 [1]
- AD_PAL_EN, PAL (B/G/I/H) Autodetect Enable, Address 0x07 [0]
- Subcarrier Frequency Lock Inversion
- Lock-Related Controls
- VS_COAST_MODE [1:0], Address 0xF9 [3:2]
- ST_NOISE_VLD, Sync Tip Noise Measurement Valid, Address 0xDE [3], Read Only
- ST_NOISE [10:0], Sync Tip Noise Measurement, Addresses 0xDE [2:0], 0xDF [7:0]
- COLOR CONTROLS
- CON [7:0], Contrast Adjust, Address 0x08 [7:0]
- SD_SAT_CB [7:0], SD Saturation Cb Channel, Address 0xE3 [7:0]
- SD_SAT_CR [7:0], SD Saturation Cr Channel, Address 0xE4 [7:0]
- SD_OFF_CB [7:0], SD Offset Cb Channel, Address 0xE1 [7:0]
- SD_OFF_CR [7:0], SD Offset Cr Channel, Address 0xE2 [7:0]
- BRI [7:0], Brightness Adjust, Address 0x0A [7:0]
- HUE [7:0], Hue Adjust, Address 0x0B [7:0]
- DEF_Y [5:0], Default Value Y, Address 0x0C [7:2]
- DEF_C [7:0], Default Value C, Address 0x0D [7:0]
- DEF_VAL_EN, Default Value Enable, Address 0x0C [0]
- DEF_VAL_AUTO_EN, Default Value Automatic Enable, Address 0x0C [1]
- CLAMP OPERATION
- LUMA FILTER
- CHROMA FILTER
- GAIN OPERATION
- Luma Gain
- Chroma Gain
- CAGC [1:0], Chroma Automatic Gain Control, Address 0x2C [1:0]
- CAGT [1:0], Chroma Automatic Gain Timing, Address 0x2D [7:6]
- CMG [11:0]/CG [11:0], Chroma Manual Gain/Chroma Gain, Address 0x2D [3:0], Address 0x2E [7:0]
- CKE, Color-Kill Enable, Address 0x2B [6]
- CKILLTHR [2:0], Color-Kill Threshold, Address 0x3D [6:4]
- CHROMA TRANSIENT IMPROVEMENT (CTI)
- DIGITAL NOISE REDUCTION (DNR) AND LUMA PEAKING FILTER
- COMB FILTERS
- NTSC Comb Filter Settings
- PAL Comb Filter Settings
- Vertical Blank Control
- NVBIOLCM [1:0], NTSC VBI Odd Field Luma Comb Mode, Address 0xEB [7:6]
- NVBIELCM [1:0], NTSC VBI Even Field Luma Comb Mode, Address 0xEB [5:4]
- PVBIOLCM [1:0], PAL VBI Odd Field Luma Comb Mode, Address 0xEB [3:2]
- PVBIELCM [1:0], PAL VBI Even Field Luma Comb Mode, Address 0xEB [1:0]
- NVBIOCCM [1:0], NTSC VBI Odd Field Chroma Comb Mode, Address 0xEC [7:6]
- NVBIECCM [1:0], NTSC VBI Even Field Chroma Comb Mode, Address 0xEC [5:4]
- PVBIOCCM [1:0], PAL VBI Odd Field Chroma Comb Mode, Address 0xEC [3:2]
- PVBIECCM [1:0], PAL VBI Even Field Chroma Comb Mode, Address 0xEC [1:0]
- AV CODE INSERTION AND CONTROLS
- BT656-4, ITU-R BT.656-4 Enable, Address 0x04 [7]
- SD_DUP_AV, Duplicate AV Codes, Address 0x03 [0]
- VBI_EN, Vertical Blanking Interval Data Enable, Address 0x03 [7]
- BL_C_VBI, Blank Chroma During VBI, Address 0x04 [2]
- RANGE, Range Selection, Address 0x04 [0]
- AUTO_PDC_EN, Automatic Programmed Delay Control, Address 0x27 [6]
- LTA [1:0], Luma Timing Adjust, Address 0x27 [1:0]
- CTA [2:0], Chroma Timing Adjust, Address 0x27 [5:3]
- SYNCHRONIZATION OUTPUT SIGNALS
- HS Configuration
- VS and FIELD Configuration
- NEWAVMODE, New AV Mode, Address 0x31 [4]
- HVSTIM, Horizontal VS Timing, Address 0x31 [3]
- VSBHO, VS Begin Horizontal Position Odd, Address 0x32 [7]
- VSBHE, VS Begin Horizontal Position Even, Address 0x32 [6]
- VSEHO VS, End Horizontal Position Odd, Address 0x33 [7]
- VSEHE, VS End Horizontal Position Even, Address 0x33 [6]
- PVS, Polarity VS, Address 0x37 [5]
- PF, Polarity FIELD, Address 0x37 [3]
- NVBEGDELO, NTSC Vsync Begin Delay on Odd Field, Address 0xE5 [7]
- NVBEGDELE, NTSC Vsync Begin Delay on Even Field, Address 0xE5 [6]
- NVBEGSIGN, NTSC Vsync Begin Sign, Address 0xE5 [5]
- NVBEG [4:0], NTSC Vsync Begin, Address 0xE5 [4:0]
- NVENDDELO, NTSC Vsync End Delay on Odd Field, Address 0xE6 [7]
- NVENDDELE, NTSC Vsync End Delay on Even Field, Address 0xE6 [6]
- NVENDSIGN, NTSC Vsync End Sign, Address 0xE6 [5]
- NVEND [4:0], NTSC Vsync End, Address 0xE6 [4:0]
- NFTOGDELO, NTSC Field Toggle Delay on Odd Field, Address 0xE7 [7]
- NFTOGDELE, NTSC Field Toggle Delay on Even Field, Address 0xE7 [6]
- NFTOGSIGN, NTSC Field Toggle Sign, Address 0xE7 [5]
- NFTOG [4:0], NTSC Field Toggle, Address 0xE7 [4:0]
- PVBEGDELO, PAL Vsync Begin Delay on Odd Field, Address 0xE8 [7]
- PVBEGDELE, PAL Vsync Begin Delay on Even Field, Address 0xE8 [6]
- PVBEGSIGN, PAL Vsync Begin Sign, Address 0xE8 [5]
- PVBEG [4:0], PAL Vsync Begin, Address 0xE8 [4:0]
- PVENDDELO, PAL Vsync End Delay on Odd Field, Address 0xE9 [7]
- PVENDDELE, PAL Vsync End Delay on Even Field, Address 0xE9 [6]
- PVENDSIGN, PAL Vsync End Sign, Address 0xE9 [5]
- PVEND [4:0], PAL Vsync End, Address 0xE9 [4:0]
- PFTOGDELO, PAL Field Toggle Delay on Odd Field, Address 0xEA [7]
- PFTOGDELE, PAL Field Toggle Delay on Even Field, Address 0xEA [6]
- PFTOGSIGN, PAL Field Toggle Sign, Address 0xEA [5]
- PFTOG, PAL Field Toggle, Address 0xEA [4:0]
- SYNC PROCESSING
- VBI DATA DECODE
- VDP Default Configuration
- VDP Manual Configuration
- MAN_LINE_PGM, Enable Manual Line Programming of VBI Standards, Address 0x64 [7], User Sub Map
- VBI_DATA_Px_Ny [3:0], VBI Standard to be Decoded on Line x for PAL, Line y for NTSC, Addresses 0x64 to 0x77, User Sub Map
- VDP_TTXT_TYPE_MAN_ENABLE, Enable Manual Selection of Teletext Type, Address 0x60 [2], User Sub Map
- VDP_TTXT_TYPE_MAN [1:0], Specify the Teletext Type, Address 0x60 [1:0], User Sub Map
- VDP Ancillary Data Output
- ADF_ENABLE, Enable Ancillary Data Output Through 656 Stream, Address 0x62 [7], User Sub Map
- ADF_DID [4:0], User-Specified Data ID Word in Ancillary Data, Address 0x62 [4:0], User Sub Map
- ADF_SDID [5:0], User-Specified Secondary Data ID Word in Ancillary Data, Address 0x63 [5:0], User Sub Map
- DUPLICATE_ADF, Enable Duplication/Spreading of Ancillary Data over Y and C Buses, Address 0x63 [7], User Sub Map
- ADF_MODE [1:0], Determine the Ancillary Data Output Mode, Address 0x62 [6:5], User Sub Map
- Structure of VBI Words in Ancillary Data Stream
- VDP Framing Code
- I2C INTERFACE
- STANDARD DETECTION AND IDENTIFICATION
- Notes
- STDI_DVALID, Standard Identification Data Valid Read Back, Address 0xB1 [7]
- STDI_LINE_COUNT_MODE, Address 0x86 [3]
- BL [13:0], Block Length Readback, Address 0xB1 [5:0], Address 0xB2 [7:0]
- LCVS [4:0], Line Count in Vsync Readback, Address 0xB3 [7:3]
- LCF [10:0], Line Count in Field Readback, Address 0xB3 [2:0], Address 0xB4 [7:0]
- FCL [12:0], 1/256th of Field Length in Number of Crystal Clocks Read back, Address 0xCA [4:0], Address 0xCB [7:0]
- STDI Readback Values for SD, PR, and HD
- I2C READBACK REGISTERS
- Teletext
- CGMS and WSS
- CC
- CC_CLEAR, Closed Captioning Clear, Address 0x78 [0], User Sub Map, Write Only, Self-Clearing
- CC_AVL, Closed Captioning Available, Address 0x78 [0], User Sub Map, Read Only
- CC_EVEN_FIELD, Address 0x78 [1], User Sub Map, Read Only
- VDP_CCAP_DATA_0, Address 0x79 [7:0], User Sub Map, Read Only
- VDP_CCAP_DATA_1, Address 0x7A [7:0], User Sub Map, Read Only
- VITC
- VPS/PDC/UTC/Gemstar
- I2C_GS_VPS_PDC_UTC (VDP) [1:0], Address 0x9C [6:5], User Sub Map
- GS_PDC_VPS_UTC_CLEAR, GS/PDC/VPS/UTC Clear, Address 0x78 [4], User Sub Map, Write Only, Self-Clearing
- GS_PDC_VPS_UTC_AVL, GS/PDC/VPS/UTC Available, Address 0x78 [4], User Sub Map, Read Only
- VDP_GS_VPS_PDC_UTC Readback Registers, Addresses 0x84 to 0x90, User Sub Map
- VPS
- Gemstar
- AUTO_DETECT_GS_TYPE, Address 0x61 [4], User Sub Map
- GS_DATA_TYPE, Address 0x78 [5], User Sub Map, Read Only
- PDC/UTC
- VBI System 2
- Gemstar Data Recovery
- GDE_SEL_OLD_ADF, Address 0x4C [3], User Map
- Gemstar Bit Names
- Gemstar 2× Format, Half-Byte Output Mode
- Gemstar 1× Format, Half-Byte Output Mode
- NTSC CC Data
- PAL CC Data
- GDECEL [15:0], Gemstar Decoding Even Lines, Address 0x48 [7:0], Address 0x49 [7:0]
- GDECOL [15:0], Gemstar Decoding Odd Lines, Address 0x4A [7:0], Address 0x4B [7:0]
- GDECAD, Gemstar Decode Ancillary Data Format, Address 0x4C [0]
- Letterbox Detection
- Detection at the Start of a Field
- Detection at the End of a Field
- Detection at the Midrange
- LB_LCT [7:0], Letterbox Line Count Top, Address 0x9B [7:0]; LB_LCM [7:0], Letterbox Line Count Mid, Address 0x9C [7:0]; LB_LCB [7:0], Letterbox Line Count Bottom, Address 0x9D [7:0]
- LB_TH [4:0], Letterbox Threshold Control, Address 0xDC [4:0]
- LB_SL [3:0], Letterbox Start Line, Address 0xDD [7:4]
- LB_EL [3:0], Letterbox End Line, Address 0xDD [3:0]
- IF Compensation Filter
- I2C Interrupt System
- Interrupt Request Output Operation
- INTRQ_DUR_SEL [1:0], Interrupt Duration Select, Address 0x40 [7:6], User Sub Map
- Interrupt Drive Level
- INTRQ_OP_SEL [1:0], Interrupt Duration Select, Address 0x40 [1:0], User Sub Map
- Multiple Interrupt Events
- Macrovision Interrupt Selection Bits
- MV_INTRQ_SEL [1:0], Macrovision Interrupt Selection Bits, Address 0x40 [5:4], User Sub Map
- PIXEL PORT CONFIGURATION
- MPU PORT DESCRIPTION
- I2C REGISTER MAPS
- PCB LAYOUT RECOMMENDATIONS
- TYPICAL CIRCUIT CONNECTION
- OUTLINE DIMENSIONS
ADV7188
Rev. A | Page 104 of 112
Bit
1
Address Register Bit Description 7 6 5 4 3 2 1 0 Comments Notes
0 Gemstar/PDC/VPS/UTC data is not
changed/available.
VDP_GS_VPS_PDC_UTC_CHNG_Q. See
Register 0x9C, Bit 5, of the user sub map to
determine whether an interrupt is issued for
a change in detected data or when data
is detected regardless of content.
1 Gemstar/PDC/VPS/UTC data is
changed/available.
Reserved. x
0 VITC data is not available in the VDP.
VDP_VITC_Q.
1 VITC data is available in the VDP.
Reserved. x
0 Does not clear. VDP_CCAPD_CLR.
1 Clears VDP_CCAPD_Q.
Reserved. x
0 Does not clear. VDP_CGMS_WSS_CHNGD_CLR.
1 Clears VDP_CGMS_WSS_CHNGD_Q.
Reserved. x
0 Does not clear. VDP_GS_VPS_PDC_UTC_CHNG_CLR.
1 Clears VDP_GS_VPS_PDC_UTC_
CHNG_Q.
Reserved. x
0 Does not clear. VDP_VITC_CLR.
1 Clears VDP_VITC_Q.
0x4F Interrupt Clear 4
(Write Only)
Reserved. x
Note that an interrupt in
Register 0x4E for the CC,
Gemstar, CGMS, WSS, VPS,
PDC, UTC, and VITC data can
be initiated by using the VDP
data slicer.
0 Masks VDP_CCAPD_Q. VDP_CCAPD_MSKB.
1 Unmasks VDP_CCAP_D_Q.
Reserved. x
0 Masks VDP_CGMS_WSS_CHNGD_Q. VDP_CGMS_WSS_CHNGD_MSKB.
1 Unmasks VDP_CGMS_WSS_CHNGD_Q.
Reserved. x
0 Masks VDP_GS_VPS_PDC_UTC_
CHNG_Q.
VDP_GS_VPS_PDC_UTC_CHNG_MSKB.
1 Unmasks VDP_GS_VPS_PDC_UTC_
CHNG_Q.
Reserved. x
0 Masks VDP_VITC_Q. VDP_VITC_MSKB.
1 Unmasks VDP_VITC_Q.
0x50 Interrupt Mask 4
Reserved. x
Note that an interrupt in
Register 0x4E for the CC,
Gemstar, CGMS, WSS, VPS,
PDC, UTC, and VITC data can
be initiated by using the VDP
data slicer.
0 0 PAL: teletext-ITU-R BT.653-625/50-A.
NTSC: reserved.
0 1 PAL: teletext-ITU-R BT.653-625/50-B
(WST). NTSC: teletext-ITU-R BT.653-
525/60-B.
1 0 PAL: teletext-ITU-R BT.653-625/50-C.
NTSC: teletext-ITU-R BT.653-525/60-C
or EIA516 (NABTS).
VDP_TTXT_TYPE_MAN [1:0].
1 1 PAL: teletext-ITU-R BT.653-625/50-D.
NTSC: teletext-ITU-R BT.653-525/60-D.
0 User programming of teletext type
disabled.
VDP_TTXT_TYPE_MAN_ENABLE.
1 User programming of teletext type
enabled.
0 Enables hamming decoding of
WST packets.
WST_PKT_DECOD_DISABLE.
1 Disables hamming decoding of
WST packets.
0x60 VDP_Config_1
Reserved.
1 0 0 0
0x61 VDP_Config_2 Reserved. x x 0 0
AUTO_DETECT_GS_TYPE. 0 Disables autodetection of
Gemstar type.
1 Enables autodetection of
Gemstar type.
Reserved. 0 0 0