Datasheet
ADV7170/ADV7171
Rev. C | Page 6 of 64
DYNAMIC SPECIFICATIONS
V
AA
= 5 V ± 5%
1
, V
REF
= 1.235 V, R
SET
= 150 Ω. All specifications T
MIN
to T
MAX
2
, unless otherwise noted.
Table 3.
Parameter Conditions
1
Min Typ Max Unit
Differential Gain
3, 4
Normal power mode 0.3 0.7 %
Differential Phase
3, 4
Normal power mode 0.4 0.7 Degrees
Differential Gain
3, 4
Lower power mode 1.0 2.0 %
Differential Phase
3, 4
Lower power mode 1.0 2.0 Degrees
SNR
3, 4
(Pedestal) RMS 80 dB rms
SNR
3, 4
(Pedestal) Peak periodic 70 dB p-p
SNR
3, 4
(Ramp) RMS 60 dB rms
SNR
3, 4
(Ramp) Peak periodic 58 dB p-p
Hue Accuracy
3, 4
0.7 1.2 Degrees
Color Saturation Accuracy
3, 4
0.9 1.4 %
Chroma Nonlinear Gain
3, 4
Referenced to 40 IRE 0.6 ±%
Chroma Nonlinear Phase
3 4
0.3 0.5 ±Degrees
Chroma/Luma Intermod
3, 4
0.2 0.4 ±%
Chroma/Luma Gain Inequality
3, 4
1.0 1.4 ±%
Chroma/Luma Delay Inequality
3, 4
0.5 2.0 ns
Luminance Nonlinearity
3, 4
0.8 1.4 ±%
Chroma AM Noise
3, 4
82 85 dB
Chroma PM Noise
3, 4
79 81 dB
1
The min/max specifications are guaranteed over this range. The min/max values are typical over 4.75 V to 5.25 V.
2
Ambient temperature range T
MIN
to T
MAX
: −40°C to +85°C. The die temperature, T
J
, must always be kept below 110°C.
3
Guaranteed by characterization.
4
These specifications are for the low-pass filter only and are guaranteed by design.
V
AA
= 3.0 V to 3.6 V
1
, V
REF
= 1.235 V, R
SET
= 150 Ω. All specifications T
MIN
to T
MAX
2
, unless otherwise noted.
Table 4.
Parameter Conditions
1
Min Typ Max Unit
Differential Gain
3
Normal power mode 1.0 %
Differential Phase
3
Normal power mode 0.5 Degrees
Differential Gain
3
Lower power mode 0.6 %
Differential Phase
3
Lower power mode 0.5 Degrees
SNR3 (Pedestal) RMS 78 dB rms
SNR3 (Pedestal) Peak periodic 70 dB p-p
SNR3 (Ramp) RMS 60 dB rms
SNR3 (Ramp) Peak periodic 58 dB p-p
Hue Accuracy
3
1.0 Degrees
Color Saturation Accuracy
3
1.0 %
Luminance Nonlinearity
3, 4
1.4 ±%
Chroma AM Noise
3, 4
80 dB
Chroma PM Noise
3, 4
79 dB
Chroma Nonlinear Gain
3, 4
Referenced to 40 IRE 0.6 ±%
Chroma Nonlinear Phase
3, 4
0.3 0.5 ±Degrees
Chroma/Luma Intermod
3, 4
0.2 0.4 ±%
1
The min/max specifications are guaranteed over this range. The min/max values are typical over 4.75 V to 5.25 V.
2
Ambient temperature range T
MIN
to T
MAX
: −40°C to +85°C. The die temperature, T
J
, must always be kept below 110°C.
3
Guaranteed by characterization.
4
These specifications are for the low-pass filter only and are guaranteed by design. For other internal filters, see Table 10.