Datasheet

REV. 0
ADuC816
–50–
I
2
C-COMPATIBLE INTERFACE
The ADuC816 supports a 2-wire serial interface mode which is
I
2
C compatible. The I
2
C-compatible interface shares its pins
with the on-chip SPI interface and therefore the user can only
enable one or the other interface at any given time (see SPE in
I2CADD I
2
C Address Register
Function Holds the I
2
C peripheral address for
the part. It may be overwritten by
user code. Technical Note uC001 at
www.analog.com/microconverter
describes the format of the I
2
C stan-
dard 7-bit address in detail.
SFR Address 9BH
Power-On Default Value 55H
Bit Addressable No
I2CDAT I
2
C Data Register
Function The I2CDAT SFR is written by the
user to transmit data over the I
2
C
interface or read by user code to read
data just received by the I
2
C interface
Accessing I2CDAT automatically
clears any pending I
2
C interrupt and
the I2CI bit in the I2CCON SFR.
User software should only access
I2CDAT once per interrupt cycle.
SFR Address 9AH
Power-On Default Value 00H
Bit Addressable No
SPICON previously). An Application Note describing the
operation of this interface as implemented is available from
the MicroConverter Website at www.analog.com/microconverter.
This interface can be configured as a Software Master or Hard-
ware Slave, and uses two pins in the interface.
SDATA (Pin 27) Serial Data I/O Pin
SCLOCK (Pin 26) Serial Clock
Three SFRs are used to control the I
2
C-compatible interface. These are described below:
I2CCON: I
2
C Control Register
SFR Address E8H
Power-On Default Value 00H
Bit Addressable Yes
ODMEDMOCMIDMMC2ISRC2IXTC2IIC2I
Table XX. I2CCON SFR Bit Designations
Bit Name Description
7 MDO I
2
C Software Master Data Output Bit (MASTER MODE ONLY).
This data bit is used to implement a master I
2
C transmitter interface in software. Data written to this
bit will be output on the SDATA pin if the data output enable (MDE) bit is set.
6 MDE I
2
C Software Master Data Output Enable Bit (MASTER MODE ONLY).
Set by user to enable the SDATA pin as an output (Tx).
Cleared by the user to enable SDATA pin as an input (Rx).
5 MCO I
2
C Software Master Clock Output Bit (MASTER MODE ONLY).
This data bit is used to implement a master I
2
C transmitter interface in software. Data written to
this bit will be outputted on the SCLOCK pin.
4 MDI I
2
C Software Master Data Input Bit (MASTER MODE ONLY).
This data bit is used to implement a master I
2
C receiver interface in software. Data on the SDATA
pin is latched into this bit on SCLOCK if the Data Output Enable (MDE) bit is ‘0.’
3 I2CM I
2
C Master/Slave Mode Bit.
Set by user to enable I
2
C software master mode.
Cleared by user to enable I
2
C hardware slave mode.
2 I2CRS I
2
C Reset Bit (SLAVE MODE ONLY).
Set by user to reset the I
2
C interface.
Cleared by user code for normal I
2
C operation.
1 I2CTX I
2
C Direction Transfer Bit (SLAVE MODE ONLY).
Set by the MicroConverter if the interface is transmitting.
Cleared by the MicroConverter if the interface is receiving.
0 I2CI I
2
C Interrupt Bit (SLAVE MODE ONLY).
Set by the MicroConverter after a byte has been transmitted or received.
Cleared automatically when user code reads the I2CDAT SFR (see I2CDAT below).
REV. A