Datasheet

ManualsBrandsANALOG DEVICES ManualsMicrocontrollers, Microprocessors & QuartzesEmbedded microcontroller LQFP 48 (7x7) 16/32-Bit 10 MHz I/O number 14

Table Of Contents

Features
Applications
General Description
Revision History
Functional Block Diagram
Specifications
- Electrical Specifications
- Timing Specifications
  - I2C Timing
  - SPI Timing
Absolute Maximum Ratings
- ESD Caution
Pin Configurations and Function Descriptions
Terminology
Overview of the ARM7TDMI Core
- Thumb Mode (T)
- Multiplier (M)
- EmbeddedICE (I)
  - ARM7 Exceptions
- ARM Registers
- Interrupt Latency
- Memory Organization
- Flash/EE Control Interface
- Memory Mapped Registers
- Complete MMR Listing
- Reset
  - RSTSTA Register
  - RSTCLR Register
Oscillator, PLL, and Power Control
- Clocking System
  - External Crystal Selection
  - External Clock Selection
- Power Control System
  - Power and Clock Control Registers
ADC Circuit Information
- Reference Sources
- Diagnostic Current Sources
- Sinc3 Filter
- ADC Chopping
- Programmable Gain Amplifier
- Excitation Sources
- ADC Low Power Mode
- ADC Comparator and Accumulator
- Temperature Sensor
- ADC MMR Interface
- Example Application Circuits
DAC Peripherals
- DAC
  - Op Amp Mode
- MMR Interface
  - DAC0CON Register
  - DAC0DAT Register
- Using the DAC
Nonvolatile Flash/EE Memory
- Flash/EE Memory Reliability
- Programming
  - Serial Downloading (In-Circuit Programming)
  - JTAG Access
Processor Reference Peripherals
- Interrupt System
- IRQ
- Fast Interrupt Request (FIQ)
- Programmed Interrupts
  - SWICFG
    - SWICFG Register
- Vectored Interrupt Controller (VIC)
- VIC MMRs
Timers
- HR:MIN:SEC: 1/128 Format
- Timer0
- Timer1 or Wake-Up Timer
- Timer2 or Watchdog Timer
- Timer3
Pulse-Width Modulator
- Pulse-Width Modulator General Overview
UART Serial Interface
- Baud Rate Generation
  - Normal 450 UART Baud Rate Generation
  - ADuC706x Fractional Divider
- UART Register Definitions
I2C
- Configuring External Pins for I2C Functionality
- Serial Clock Generation
- I2C Bus Addresses
  - Slave Mode
  - Master Mode
- I2C Registers
Serial Peripheral Interface
- MISO (Master In, Slave Out) Pin
- MOSI (Master Out, Slave In) Pin
- SCLK (Serial Clock I/O) Pin
- Slave Select (P0.0/) Input Pin
- Configuring External Pins for SPI Functionality
- SPI Registers
General-Purpose I/O
- GPxCON Registers
- GPxDAT Registers
- GPxSET Registers
- GPxCLR Registers
- GPxPAR Registers
  - GP0CON1 Control Registers
Hardware Design Considerations
- Power Supplies
Outline Dimensions
- Ordering Guide

Data Sheet ADuC7060/ADuC7061

Rev. D | Page 79 of 108

PWM2COM0 Compare Register

Name: PWM2COM0

Address: 0xFFFF0FA4

Default value: 0x0000

Access: Read and write

Function: PWM4 output pin goes high when the PWM

timer reaches the count value stored in this

PWM2COM1 Compare Register

Name: PWM2COM1

Address: 0xFFFF0FA8

Default value: 0x0000

Access: Read and write

Function: PWM4 output pin goes low when the PWM

timer reaches the count value stored in this

PWM2COM2 Compare Register

Name: PWM2COM2

Address: 0xFFFF0FAC

Default value: 0x0000

Access: Read and write

Function: PWM5 output pin goes low when the PWM

timer reaches the count value stored in this

PWM2LEN Register

Name: PWM2LEN

Address: 0xFFFF0FB0

Default value: 0x0000

Access: Read and write

Function: PWM5 output pin goes high when the PWM

timer reaches the value stored in this register.

PWMCLRI Register

Name: PWMCLRI

Address: 0xFFFF0FB8

Default value: 0x0000

Access: Write only

Function: Write any value to this register to clear a

PWM interrupt source. This register must be

written to before exiting a PWM interrupt

service routine; otherwise, multiple interrupts

occur.