Datasheet
Table Of Contents
- Blackfin Dual Core Embedded Processor
- Features
- Memory
- Table Of Contents
- Revision History
- General Description
- ADSP-BF60x Detailed Signal Descriptions
- 349-Ball CSP_BGA Signal Descriptions
- GP I/O Multiplexing for 349-Ball CSP_BGA
- ADSP-BF60x Designer Quick Reference
- Specifications
- Operating Conditions
- Electrical Characteristics
- Processor — Absolute Maximum Ratings
- ESD Sensitivity
- Processor — Package Information
- Timing Specifications
- Clock and Reset Timing
- Power-Up Reset Timing
- Asynchronous Read
- Asynchronous Flash Read
- Asynchronous Page Mode Read
- Synchronous Burst Flash Read
- Asynchronous Write
- Asynchronous Flash Write
- All Accesses
- Bus Request/Bus Grant
- DDR2 SDRAM Clock and Control Cycle Timing
- DDR2 SDRAM Read Cycle Timing
- DDR2 SDRAM Write Cycle Timing
- Mobile DDR SDRAM Clock and Control Cycle Timing
- Mobile DDR SDRAM Read Cycle Timing
- Mobile DDR SDRAM Write Cycle Timing
- Enhanced Parallel Peripheral Interface Timing
- Link Ports
- Serial Ports
- Serial Peripheral Interface (SPI) Port—Master Timing
- Serial Peripheral Interface (SPI) Port—Slave Timing
- Serial Peripheral Interface (SPI) Port—SPI_RDY Slave Timing
- Serial Peripheral Interface (SPI) Port—Open Drain Mode Timing
- Serial Peripheral Interface (SPI) Port—SPI_RDY Timing
- General-Purpose Port Timing
- Timer Cycle Timing
- Up/Down Counter/Rotary Encoder Timing
- Pulse Width Modulator (PWM) Timing
- ADC Controller Module (ACM) Timing
- Universal Asynchronous Receiver-Transmitter (UART) Ports—Receive and Transmit Timing
- CAN Interface
- Universal Serial Bus (USB) On-The-Go—Receive and Transmit Timing
- RSI Controller Timing
- 10/100 Ethernet MAC Controller Timing
- JTAG Test And Emulation Port Timing
- Output Drive Currents
- Environmental Conditions
- ADSP-BF60x 349-Ball CSP_BGA Ball Assignments
- Outline Dimensions
- Automotive Products
- Ordering Guide
Rev. 0 | Page 88 of 112 | June 2013
ADSP-BF606/ADSP-BF607/ADSP-BF608/ADSP-BF609
Serial Peripheral Interface (SPI) Port—Open Drain Mode
Timing
In Figure 39 and Figure 40, the outputs can be SPI_MOSI SPI_
MISO, SPI_D2, and/or SPI_D3 depending on the mode of
operation.
Table 54. SPI Port ODM Master Mode Timing
V
DD_EXT
1.8 V/3.3 V Nominal
Parameter Min Max Unit
Switching Characteristics
t
HDSPIODMM
SPI_CLK Edge to High Impedance from Data Out Valid –1 ns
t
DDSPIODMM
SPI_CLK Edge to Data Out Valid from High Impedance 0 6 ns
Figure 39. ODM Master
Table 55. SPI Port—ODM Slave Mode
V
DD_EXT
1.8 V/3.3 V Nominal
Parameter Min Max Unit
Timing Requirements
t
HDSPIODMS
SPI_CLK Edge to High Impedance from Data Out Valid 0 ns
t
DDSPIODMS
SPI_CLK Edge to Data Out Valid from High Impedance 11.5 ns
Figure 40. ODM Slave
SPI_CLK
(CPOL = 0)
t
HDSPIODMM
SPI_CLK
(CPOL = 1)
t
DDSPIODMM
t
DDSPIODMM
t
HDSPIODMM
OUTPUT
(CPHA = 1)
OUTPUT
(CPHA = 0)
t
HDSPIODMS
t
DDSPIODMS
t
DDSPIODMS
t
HDSPIODMS
SPI_CLK
(CPOL = 0)
SPI_CLK
(CPOL = 1)
OUTPUT
(CPHA = 1)
OUTPUT
(CPHA = 0)