Datasheet

REV. 0
–8–
ADSP-2188M
Terminating Unused Pins
The following table shows the recommendations for terminating unused pins.
Pin Terminations
I/O 3-State Reset Hi-Z*
Pin Name (Z) State Caused By Unused Configuration
XTAL I I Float
CLKOUT O O Float
A13:1 or O (Z) Hi-Z BR, EBR Float
IAD 12:0 I/O (Z) Hi-Z IS Float
A0 O (Z) Hi-Z BR, EBR Float
D23:8 I/O (Z) Hi-Z BR, EBR Float
D7 or I/O (Z) Hi-Z BR, EBR Float
IWR I I High (Inactive)
D6 or I/O (Z) Hi-Z BR, EBR Float
IRD IIBR, EBR High (Inactive)
D5 or I/O (Z) Hi-Z Float
IAL I I Low (Inactive)
D4 or I/O (Z) Hi-Z BR, EBR Float
IS I I High (Inactive)
D3 or I/O (Z) Hi-Z BR, EBR Float
IACK Float
D2:0 or I/O (Z) Hi-Z BR, EBR Float
IAD15:13 I/O (Z) Hi-Z IS Float
PMS O (Z) O BR, EBR Float
DMS O (Z) O BR, EBR Float
BMS O (Z) O BR, EBR Float
IOMS O (Z) O BR, EBR Float
CMS O (Z) O BR, EBR Float
RD O (Z) O BR, EBR Float
WR O (Z) O BR, EBR Float
BR I I High (Inactive)
BG O (Z) O EE Float
BGH O O Float
IRQ2/PF7 I/O (Z) I Input = High (Inactive) or Program as Output, Set to 1, Let Float
IRQL1/PF6 I/O (Z) I Input = High (Inactive) or Program as Output, Set to 1, Let Float
IRQL0/PF5 I/O (Z) I Input = High (Inactive) or Program as Output, Set to 1, Let Float
IRQE/PF4 I/O (Z) I Input = High (Inactive) or Program as Output, Set to 1, Let Float
SCLK0 I/O I Input = High or Low, Output = Float
RFS0 I/O I High or Low
DR0 I I High or Low
TFS0 I/O I High or Low
DT0 O O Float
SCLK1 I/O I Input = High or Low, Output = Float
RFS1/IRQ0 I/O I High or Low
DR1/FI I I High or Low
TFS1/IRQ1 I/O I High or Low
DT1/FO O O Float
EE I I Float
EBR I I Float
EBG O O Float
ERESET I I Float
EMS O O Float
EINT I I Float
ECLK I I Float
ELIN I I Float
ELOUT O O Float
NOTES
*Hi-Z = High Impedance.
1. If the CLKOUT pin is not used, turn it OFF, using CLKODIS in SPORT0 autobuffer control register.
2. If the Interrupt/Programmable Flag pins are not used, there are two options: Option 1: When these pins are configured as INPUTS at reset and function as inter-
rupts and input flag pins, pull the pins High (inactive). Option 2: Program the unused pins as OUTPUTS, set them to 1, prior to enabling interrupts, and let pins float.
3. All bidirectional pins have three-stated outputs. When the pin is configured as an output, the output is Hi-Z (high impedance) when inactive.
4. CLKIN, RESET, and PF3:0/MODE D:A are not included in the table because these pins must be used.