Datasheet

ADM2483 Data Sheet
Rev. F | Page 6 of 18
PACKAGE CHARACTERISTICS
Table 5.
Parameter Symbol Min Typ Max Unit Test Conditions
Resistance (Input-Output)
1
R
I-O
10
12
Ω
Capacitance (Input-Output)
1
C
I-O
3 pF f = 1 MHz
Input Capacitance
2
C
I
4 pF
Input IC Junction-to-Case Thermal Resistance θ
JCI
33 °C/W
Thermocouple located at center of package
underside
Output IC Junction-to-Case Thermal Resistance θ
JCO
28 °C/W
Thermocouple located at center of package
underside
1
Device considered a 2-terminal device: Pins 1, 2, 3, 4, 5, 6, 7, and 8 shorted together, and Pins 9, 10, 11, 12, 13, 14, 15, and 16 shorted together.
2
Input capacitance is from any input data pin to ground.
REGULATORY INFORMATION
The ADM2483 has been approved by the following organizations:
Table 6.
UL
1
CSA CQC VDE
2
Recognized Under 1577
Component
Recognition Program
Approved under CSA
Component Acceptance
Notice 5A
Approved Under
CQC11-471543-2012
Certified according to
DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12
IEC 609501 800 V rms
(1131 V
PEAK
) basic, 400 V rms
(565 V
PEAK
) reinforced
Basic insulation per
GB4943.1-2011, 415 V rms
(588 V
PEAK
) maximum working
voltage, tropical climate,
altitude ≤ 5000 meters
Reinforced insulation, V
IORM
= 565 V peak,
V
IORM(DC)
= 1500 V dc
File E214100
File 205078
File CQC14001114898
File 2471900-4880-0001
1
In accordance with UL1577, each ADM2483 is proof tested by applying an insulation test voltage ≥3000 V rms for 1 sec (current leakage detection limit = 5 µA).
2
In accordance with VDE V 0884-10, each ADM2483 is proof tested by applying an insulation test voltage ≥2813 V
PEAK
for 1 sec (partial discharge detection limit = 5 pC).
INSULATION AND SAFETY-RELATED SPECIFICATIONS
Table 7.
Parameter Symbol Value Unit Conditions
Rated Dielectric Insulation Voltage 2500 V rms 1-minute duration
Minimum External Air Gap (Clearance) L(I01) 7.6 min mm
Measured from input terminals to output
terminals, shortest distance through air
Minimum External Tracking (Creepage)
L(I02)
7.6 min
mm
Measured from input terminals to output
terminals, shortest distance along body
Minimum Clearance in the Plane of the Printed Circuit
Board (PCB Clearance)
L(PCB) 8.1 min mm
Minimum Internal Gap (Internal Clearance) 0.017 min mm Insulation distance through insulation
Tracking Resistance (Comparative Tracking Index) CTI
>400 or
>600
V DIN IEC 112/VDE 0303 Part 1
1
Isolation Group I or II Material Group (Table 1 in DIN VDE 0110,1/89)
1
1
An ampersand (&) on the physical package denotes the CSA attestation of CTI>600 V and isolation of Material Group I.
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.