Datasheet

Data Sheet ADA4898-1/ADA4898-2
APPLICATIONS INFORMATION
HIGHER FEEDBACK RESISTOR GAIN OPERATION
The ADA4898-1/ADA4898-2 schematic for the noninverting
gain configuration shown in Figure 45 is nearly a textbook
example. The only exception is the feedback capacitor in
parallel with the feedback resistor, R
F
, but this capacitor is
recommended only when using a large R
F
value (>300 Ω).
Figure 46 shows the difference between using a 100 Ω resistor
and a 1 kΩ feedback resistor. Due to the high input capacitance in
the ADA4898-1/ADA4898-2 when using a higher feedback
resistor, more peaking appears in the closed-loop gain. Using
the lower feedback resistor resolves this issue; however, when
running at higher supplies (±15 V) with an R
F
of 100 Ω, the
system draws a lot of extra current into the feedback network.
To avoid this problem, a higher feedback resistor can be used
with a feedback capacitor in parallel. Figure 46 shows the effect of
placing a feedback capacitor in parallel with a larger R
F
. In this
gain-of-2 configuration, R
F
= R
G
= 1 kΩ and C
F
= 2.7 pF. When
using C
F
, the peaking drops from 6 dB to less than 2 dB.
07037-043
V
IN
V
OUT
10µF
+V
S
–V
S
R
T
R
L
+
10µF
+
C
F
R
F
R
F
0.1µF
0.1µF
Figure 45. Noninverting Gain Schematic
–15
–12
–9
–6
–3
0
3
6
9
12
07037-044
FREQUENCY (Hz)
CLOSED-LOOP GAIN (dB)
100k
10M
1M
100M
R
F
= 1kΩ, C
F
= 2.7pF
R
F
= 1kΩ
R
F
= 100Ω
G = +2
R
L
= 1kΩ
V
S
= ±15V
Figure 46. Small Signal Frequency Response for
Various Feedback Impedances
RECOMMENDED VALUES FOR VARIOUS GAINS
Table 8 provides a useful reference for determining various gains
and associated performance. R
F
is set to 100 Ω for gains greater
than 1. A low feedback R
F
resistor value reduces peaking and
minimizes the contribution to the overall noise performance
of the amplifier.
Table 8. Gains and Recommended Resistor Values Associated with Them (Conditions: V
S
= ±5 V, T
A
= 25°C, R
L
= 1 kΩ, R
T
= 49.9 Ω)
Gain R
F
(Ω) R
G
(Ω)
−3 dB SS BW (MHz),
V
OUT
= 100 mV p-p
Slew Rate (V/µs),
V
OUT
= 2 V Step
ADA4898-1/ADA4898-2
Voltage Noise (nV/√Hz), RTO
Total System Noise
(nV/√Hz), RTO
+1 0 Not applicable 65 55 0.9 1.29
[phone] 1.8 3.16
+5 100 24.9 9 45 4.5 7.07
Rev. E | Page 15 of 20
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.