Datasheet

AD9520-0 Data Sheet
Rev. A | Page 66 of 80
Reg.
Addr.
(Hex)
Bits Name Description
[2:0] Prescaler P
Prescaler: DM = dual modulus; FD = fixed divide. Prescaler P is part of the feedback divider. See the VCO/VCXO Feedback Divider
N—P, A, and B section of the datasheet for details.
Bit
2
Bit
1
Bit
0 Mode Prescaler
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
FD
FD
DM
DM
DM
DM
DM
FD
Divide-by-1.
Divide-by-2.
Divide-by-2 and divide-by-3 when A ≠ 0; divide-by-2 when A = 0.
Divide-by-4 and divide-by-5 when A ≠ 0; divide-by-4 when A = 0.
Divide-by-8 and divide-by-9 when A ≠ 0; divide-by-8 when A = 0.
Divide-by-16 and divide-by-17 when A ≠ 0; divide-by-16 when A = 0.
Divide-by-32 and divide-by-33 when A ≠ 0; divide-by-32 when A = 0 (default).
Divide-by-3.
0x017 [7:2]
STATUS
pin control
Selects the signal that appears at the STATUS pin. Register 0x01D[7] must be 0b to reprogram the STATUS pin.
Bit
7
Bit
6
Bit
5
Bit
4
Bit
3
Bit
2
Level or
Dynamic
Signal
Signal at STATUS Pin
0 0 0 0 0 0 LVL Ground (dc) (default).
0 0 0 0 0 1 DYN N divider output (after the delay).
0 0 0 0 1 0 DYN R divider output (after the delay).
0 0 0 0 1 1 DYN A divider output.
0 0 0 1 0 0 DYN Prescaler output.
0 0 0 1 0 1 DYN PFD up pulse.
0 0 0 1 1 0 DYN PFD down pulse.
0 X X X X X LVL Ground (dc). Used for all settings of these bits that are not otherwise specified in this table.
The selections that follow are also used for REFMON and LD pin control.
1 0 0 0 0 0 LVL Ground (dc).
1 0 0 0 0 1 DYN REF1 clock (differential reference when in differential mode).
1 0 0 0 1 0 DYN REF2 clock (N/A in differential mode).
1 0 0 0 1 1 DYN Selected reference to PLL (differential reference when in differential mode).
1
0
0
1
0
0
DYN
Unselected reference to PLL (not available in differential mode).
1
0
0
1
0
1
LVL
Status of selected reference (status of differential reference); active high.
1 0 0 1 1 0 LVL Status of unselected reference (not available in differential mode); active high.
1 0 0 1 1 1 LVL Status of REF1 frequency; active high.
1 0 1 0 0 0 LVL Status of REF2 frequency; active high.
1 0 1 0 0 1 LVL (Status of REF1 frequency) AND (status of REF2 frequency).
1 0 1 0 1 0 LVL (DLD) AND (status of selected reference) AND (status of VCO).
1 0 1 0 1 1 LVL Status of VCO frequency; active high.
1 0 1 1 0 0 LVL Selected reference (low = REF1, high = REF2).
1 0 1 1 0 1 LVL DLD; active high.
1 0 1 1 1 0 LVL Holdover active; active high.
1 0 1 1 1 1 LVL N/A. Do not use.
1 1 0 0 0 0 LVL V
S
(PLL power supply).
1 1 0 0 0 1 DYN
REF1 clock
(differential reference when in differential mode).
1 1 0 0 1 0 DYN
REF2 clock
(not available in differential mode).
1 1 0 0 1 1 DYN
Selected reference to PLL
(differential reference when in differential mode).
1 1 0 1 0 0 DYN
Unselected reference to PLL
(not available when in differential mode).
1 1 0 1 0 1 LVL Status of selected reference (status of differential reference); active low.
1 1 0 1 1 0 LVL Status of unselected reference (not available in differential mode); active low.
1 1 0 1 1 1 LVL Status of REF1 frequency; active low.
1
1
1
0
0
0
LVL
Status of REF2 frequency; active low.
1
1
1
0
0
1
LVL
(Status of REF1 frequency) AND (status of REF2 frequency)
.
1
1
1
0
1
0
LVL
(DLD) AND (status of selected reference) AND (status of VCO)
.
1 1 1 0 1 1 LVL Status of VCO frequency; active low.
1 1 1 1 0 0 LVL Selected reference (low = REF2, high = REF1).
1 1 1 1 0 1 LVL DLD; active low.
1 1 1 1 1 0 LVL Holdover active; active low.
1 1 1 1 1 1 LVL N/A. Do not use.